I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hi,
I have created a project with Keil 5.15
The simply blink app works. Now I want to play with softdevice.
The only problem is... no matter what I do, my hex file always...
Hi ALl
I have permanent error on connect command {0x05, 0x0F, 0x3f, 0xff, 0x40, 0x00 }
When I use security option, with or without PassKey. Return message is 01-03-84...
hey,
so today I updated my NRF Tools... I guess i was using an old version before.
To test our prototypes we have a test fixture where the board is programmed at the...
I'm looking to maximize the throughput using Gazelle on the nRF51.
Assuming zero retransmissions, I believe the theoretical max should be (1/TimeslotPeriod)*PayloadSize...
There is some doubt about the nRF2401L+ RF matching circuit.From the article of <<Tuning_the_nFR24xx_matching_network.pdf>> ,it says "The balun-function is done by the 180...
Is it possible for a nrf51822 running s130 to advertise and scan at the same time?
I am trying to scan for other BLE devices using s130 softdevice, but cannot find an example...
Hi,
I have learned that you can change the MAC address on a device by using sd_ble_gap_address_set. However, when I press the sw2 button on the beacon (running a modified...
While reading about setting up nRF51 development environment on OS X , I came across the following:
Unfortunately the only way to erase
the memory is to do some magic...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
I've tried to set up my own BLE project as an exercise in understanding what's going on. It's going okay, with the exception that the device isn't advertising the data that...
I write PWR_UP using SPI and then read the Reg <0>. but I am not getting what I wrote.
Step 1 : Power ON using 3V.
Step 2 : Delay for 1 Sec to get into POWER DOWN MODE...
Hello,
On my custom board, I'm receiving chunks of UART data, without flow control, at 115200bps. Sometimes (its quite frequent now... sometimes after 10 chunks, sometimes...
