I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
On the nRF51, LO leakage was measured when in receive mode. For 2402~2480mhz, LO leakage was measured at approximately 2745~2836mhz. The nRF52 does not measure LO leakage...
Hi,
I am using nrf52832 board and I want to configure the SPI0 and SPI1 for the sensors LIS2DW and BMP388 respectively.
I am new to nRF Connect SDK for VS code, I am exploring...
I have installed version 5.0.2 for NRF connect Desktop and on that I have been trying different versions of tool chain manager ranging 1.3.0 to 1.5.1 none of them is loading...
To measure the current consumption during system off on the NRF52833DK, I followed these steps:
Cut the SB40 bridge.
Connected a multimeter to P22.
Here's what I...
Hello,
I would like to analyze the nfc_launchapp example from the SDK to understand how NFC tags are recognized.
Specifically, I want to examine the relevant code portions...
I'm using the peripheral AES CCM to encrypt frames on the nrf52832 board but I'm not using the on-the-fly encryption (at the same time as the radio).
I managed to correctly...
I was following this lesson on paring and passkey authentication:
Exercise 1 - Nordic Developer Academy (nordicsemi.com)
Is there a way to get the popup for the pin...
Hello DevZone,
I am using a nRF52840 with sdk 17.0.2 with Windows 10
I am trying to setup a connection to my Windows PC but I noticed data fragmentation and a queue...
I would like to analyze the nfc_launchapp example from the SDK to understand how NFC tags are recognized. Specifically, I want to examine the relevant code portions.
However...
After installing the nRF Connect for VS Code extension pack and trying to access the nRF Connect for VS Code extension, it keeps loading indefinitely. This is halting any...
Hello, we have application based on ncs v2.7.0. We use cmakepreset and cmake for building application. We want to add DFU functionality to our project. We study following...
Hello everyone,
I'm currently using nRf52840 dongle for my project for building communication between nrd52840 dongle and development kit, I'm currently running the C...
I have an array of LEDs on my custom board. One of the LEDs is set on a UART0 RTS pin, which is GPIO(0,5), and we are using ground as common. To avoid any conflicts, I disabled...
Hello,
As mentioned we have a custom board and we are now enabling bluetooth. Given that we are using the nRF5340 we have a custom CPUNET board defined (we just took the...
Hi, I am newbie to the nordic world. I am trying to developing an application that allows me to send data via UART ("not using the ble " )from nordic nRF5340 board and read...
