Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Here is a warning I get linking an application that uses nRF DM library 5/14] Linking C static library app\libapp.a [6/14] Linking C executable zephyr\zephyr_pre0.elf c:/toolchains...
Hi,
Can any one list what are the reasons for sd_ble_gap_connect returns NRF_ERROR_DATA_SIZE?
In ble_gap.h NRF_ERROR_DATA_SIZE error code doesn't exist for sd_ble_gap_connect...
Hello,
We have already product with BLE 4 and now we are moving to BLE5. As per the example code we have updated our code to BLE 5 but we are not seeing advertisement...
Purpose: to develop a central device using nRF5340 and to enable both BLE Mesh and AoA features.
Questions:
1. nRF5 SDK supports nRF51 and nRF52 series but not for nRF5340...
Hello,
We were middle way during the development when we found out that we had a higher packet loss than what is acceptable.
So we start to analyze this issue.
Scenario...
Hi,
I reviewed the PCA10121 schematic for using SPI4 pins to connect to Semtech SX1262. Since SPI4 bus also connected to SD card and DSP. I checked to see if SPI0..3 pins...
In my application, we regularly transmit a stream of notifications from a Peripheral Server to a Central Client. The general strategy for this is to enqueue a packet, and...
Hello in my app I based it on the BLE UART example and have it pretty much up and running but I need to be able to send multiple messages from the Central to the Peripheral...
I am tring to update the DK bootloader by entering the maintenance mode by pressing the reset button while plugging in the DK, but the board does not show on my PC
any help...
Hi,
I do have Zephyr's logging configured using RTT for debugging messages and in general this works.
Sadly when reflashing (via SWD) the RTT stops working and I have...
Hello,
We are using nrf52832 and SDK15.3 in our product, which sends about 7.4K bytes data every second to an Android phone.
4 ble devices are connected to the phone and...
Hi experts,
I habe a following issue. First I have tried to use nrfx_twi driver. There was any data send over I2C... So I have written own driver using the Datasheet and...
We are trying to send a large message via a BLE characteristic and to do that we have broken up the message payload into smaller fragments and calling bt_gatt_notify() repeatedly...
hi：
I use ble_app_uart routine, test the receiving rate, use the mobile phone to send data, 52832 receive the fastest can only be 10KB.
In addition, when the interval...
