Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hi!
I am evaluating some nrf9151 boards using the DECT NR+ stack. I have made my own PING test using UDP to test latency and loss.
Setup: nRF Connect SDK v3.3.1, DECT...
As in topic I'am concerned about the impedance of SWD interface drivers.
I'am building and SWD interface multiplexer that will be used with 48 devices using J-Link Pro debugger...
Hi team,
I recently purchased some nRF54LM20A units and I am currently working on interfacing them with a W5500 Ethernet module over SPI. However, I am facing difficulties...
Hello, I am trying to configure the NRF9151-DK, but when opening Quickstart app it cannot verify the board. Here's the log. I've been working with exact same boards, also...
I just programmed 2 Boards.
One Peripheral advertising with 1m Phy and other peripheral with s8 codded phy.
Using NRF connect app and wire sharc I made sure that I really...
I had TWO DKs as described in the title randomly fail on me in the same way, months apart. Additionally, I had an earlier rev DK, 2.1.0 (NRF5340 is NOT the IMCU on this version...
Hi,
I'm working on a project with the nRF52840 using nRF5 SDK v15.3.0 and have been working on enabling dual-bank DFU in the bootloader. During this process I made several...
Dear Nordic
There are two questions. Thanks
Q1. Did you have temperature test report of nRF54LM20A (with NFC functionality)?
Q2. We want to implement FIDO (Fast Identity...
Hi,
I am new to Nordic environment.
I have a project build on nrf5340_cpuapp_ns. I want to enable logs on both non-secure and secure image.
Currently I am only seeing...
Description ===========
I am trying to use the native HTTP/HTTPS AT commands of the nRF93M1 to download a firmware image for an external host MCU.
Hardware and software...
Hello,
I ma gathering some data from nRFCloud API, and I noticed a small issue with the pageNextToken. I noticed this on https://api-docs.nrfcloud.com/#tag/FOTA-Job-Executions...
Hi
In my project I have set CONFIG_BT_AUTO_PHY_UPDATE=n in prj.conf. I am using NRF connect sdk 3.4.0
I have configured both central and peripheral to s8 advertising and...
I'm trying to capture a ble connection with nrfutil. What I've done:
- installed nrfutil on my arch based linux machine
- install ble-sniffer
- setup the nRF52840 Dongle...
Hello Nordic team,
I am working with an nRF54L15dk and have an issue using P0.01 as a GPIO input.
P0.03 works correctly with the same GPIO configuration, but P0.01 does...
This is a follow up to case 356908 which was closed due to no resources available. --- We need to shutdown the modem or we end up locking it in the reset-protection state...
