Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hi,
I am using nrf52810 with custom board and i want to create OTA file for custom application. while compiling the bootloader to get hex files, i am getting error as "Target...
from the datasheet we see that this device can operate at 1.8V or 3V3 (or anything in between).
We can also check supply current on the mRF52DK which runs at 3V3.
How...
Hi everyone,
I would like to measure the total current consumption of the board in order to get an estimation of the battery life. I am using PPK-2 and nRF Connect Power...
Hello Everyone,
For my project, I have to make my BLE device to advertise itself for a period of time and transit to "scan" mode to scan for other device for a period of...
I am getting this fault when i try to run a observer handler where i have implemented semaphores.
And i cant figure out what this error code means
Thanks in advan...
Hello,
I am currently trying to run this ble_secure_bootloader . I am using SES V5.68 with the nRF52840 SoC and I am using nRF5 SDK version 14.2.0. I have also adjusted...
Hi Team,
I want to know the time with time resolution milliseconds for initialization time of nrf52840 chips and nrf52840 DK with external supply model?
KInd regards,...
Hi,
The below code I believe is in error. The below write operation overwrites the LIO2, LIO3, WIPWAIT, and WREN settings in the CINSTRCONF register by only writing the...
First off, It's great you guys are setting a high pace with development and improving the SDK but I and I think many other people would like it if you change a full version...
Hi!
I am currently working on this sample with an nrf52840 board and a nrf52832 board:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/peripheral...
Hi All!
Hope you are doing well! I am using nrf52840 and nrf58233. Is there any example available for both transmitter and receiver for connectable coded PHY beacons?...
I am trying to determine the best way to debounce 7 digital inputs with 2 bounce times ranging between 50 ms to 2 seconds. I thought of using the GPIOTE but that seems to...
Hi All,
I asked this question before but I accidentally pressed close.
The engineer told me that f or nRF5 SDK ( I assume as you said Segger), you can send 10 byte long...
I'm working with the project based on nrf52833 and SDK 17. I've noticed that when there are no devices on I2C bus, the application stucks on nrf_drv_twi_tx function, and the...
Hi , I'm using nrf5340 and nrf connect sdk 1.5.1 , recently I found out when sending large amount of data with low RSSI through bt_gatt_notify_cb the system would enter some...
