I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
As the poster above mentioned, the nRF54L15 ENGA version is stuck when initializing the GRTC.
it gets stuck at nrfy_grtc_sys_counter_start().
The SDK is 3.0.2.
Is there...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
We are developing a BLE application with nRF52833 512kB ROM size and using NCS v3.0.2. However it seems the ROM size occupied is not so logical, or the ROM size for NCS (Zephyr...
Hello,
I am having nRF9160 with modem FW = 1.3.6 and nrf sdk version 2.7.0
I am using MBEDTLS library for generating self-signed & CSR certificates with EC-Key and RSA...
I was doing development on the development kit and I noticed that when flashing the device there is application core and modem core firmware that is flashed
I'm trying to...
I am using the nRF54L15 on a custom board where I have good control and knowledge about what is going on regarding current consumption. I am using an MX25R64 external flash...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
I am currently developing a project using the nRF51822 with SoftDevice S110 v8.0.3 in Keil uVision.
To properly manage RTE components and dependencies, I need to use the...
Hi
In my ble repeater application on nRF52833, when I adding OTA function , I found the my image rom size too large to adding FOTA with MCUBoot. there is my memory report...
Hi,
I am currently implementing an E-Ink display application using the SPI interface on our custom nRF54L15 board. I initially configured the display with the following...
Hi All,
I'm currently working with a custom board using the NPM1300 and STM32L4, alongside the npmx drivers. I'm trying to capture both pressed and released events from...
Hi, I'm currently in architecture definition stage, and I'd like to know more about the possibilities driven by Channel Sounding. From what I understand, you can only perform...
Hi,
I have two nearly identical revisions of a board with an nrf5340 which behave differently in a curious way:
On one revision I can issue a "mon reset" command in...
Hello
I'm working on a custom electronics board with an nrf54L15 (QFAA). This MCU is interfaced with an EEPROM memory (24FC16T) via an I2C bus connected on P1.03(SCL) and...
Hi,
I am working on ncs 2.9.1 @ nRF54L15.
I followed this academy course to add a single channel saadc in simple mode:
ADC read works properly, but the current read...
