hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Dear all, now I am making a data sampling system with multi peripherals and one central. The peripherals sample data from sensor via SPI port and transmit data to the central...
Any SSD1306 example for nrf51822 ??? I found this but is for nrf52.. i try to add it for my nrf51822 but there are tons of functions with different declarations in my sdk...
I have nRF5340dk board and my question is that can I use only networking processor to run the BLE applications? If not why? As the Radio hardware is only connected to networking...
Hello , I want to read analog values from potentiometer using analog pin P0.04 (A0) on nrf5340 with zephyr ecosystem . Where can I get beginner documentation like setting...
Hi,
I'm a beginner, and currently working to implement a low-power controller using nRF52-DK and Power Profiler Kit (PPK).
I ran the following codes (system off) and expected...
I have setup a 1-1 paired central(+peripheral) <=> peripheral Central is a 52832, SDK 16.0, SD s132 v7.0.1 peripheral is a 52811, SDK 16.0, SD s112 v7.0.1 My code is based...
in this example
/root/ncs/nrf/applications/serial_lte_modem
I want to build_nrf9160dk_nrf9160 in secure mode
but compile error #ifndef CONFIG_TRUSTED_EXECUTION_NONSECURE...
Hello,
I am confused on which plateform I should use to program my nrf52832 chip.
First it is advertised to use Segger Embedded Studio that I am trying to configure...
Hi all. I am using Keil for programming a nrf51822 & SDK 12.3 I want to use the SSD1306 OLED Drivers in my project I follow these steps: 1) I copy .c and .h files form github...
Hello,
Im using a NRF52840 custom made board and im having some issue with the I2C communication. There are 3 units on the I2C line, the MCU and two sensors, the diagram...
Hello,
I am doing a project for college with nRF52840. It's about a mobile phone with an app that send the location of the device when a user touch a button. This message...
I'm using the nRF52805 BLE function to send senor data to my phone (Android). In nRF Connect App, the data updates at a quick speed, which is expected (see image 1). I would...
Using Keil uVision 5.33 together with Nordic SDK 14.1.0
I'm not able to compile+link the example "ble_peripheral \ ble_app_hids_keyboard" because the code exceeds 32 kBytes...
Hi,
I using the radio test on the nrf52840 for RF verification, but now we want to reduce the latency from 8ms to 1ms.
Is the radio test project can modify the latency...
I have Raspbery pi flashed with nordic alpha 4.1.0.1 image + nrf52840 dongle in NCP design .
As an end device I have EFR32 MG12 WSTK flashed with OT-CLI-FTD code and connected...
