I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hi,
I have a custom board with nRF52840 and I'm using nordic SDK. My image size is increasing because I have lots of peripheral connected in my board. I would like to use...
Hi, I'm about to perform an RF-PHY test on a module using nRF8001 to get a QDID. In that connection, I would like to know the specifications of the nRF8001.Can you tell me...
Hii ,
Iam using nordic nrf52832 board In the example of ble_att_mtu_throughput example . I have tried a lot to achieve the 803 kbps, but the output was 204 kbps only....
I want to implement integration tests of the ZigBee subsystem on nrf52 and looking for a way to launch them by CI script. We need such a feature for automatic testing after...
If we were to run a 52832 as a BLE advert receiver - listening permanently for BLE adverts - do you have any information of the expected current consumption in this kind of...
Hi!
I want to program boards in production by using the SWD interface from a nRF52840. The image will be sent from a PC to the nRF through the USB-virtual serial port. ...
Download nrf52832 through JLINK tool, and then through jflash read back, it is found that the bin file is different from the download in bin file. What is the composition...
Hello, i work with nrf52840. I know that it is possible to run two stacks Thread and BLE on one Chip (nRF52840) on dynamic way. But i want to run Thread as NCP-Radio and BLE...
Is there a graph available for the internal power regulators efficiency / current consumption at different supply voltages and temperatures for the nRF9160(-SICA)? We're currently...
I need to create a health device that sends time stamps of the measurement. For that to work I would need the counter to continue between power cycles. Some devices have a...
When the program runs, it will enter the hardware fault，because part of the code is lost in the program storage area of flash.
As shown in the figure, the left part is...
I want to implement lwm2m, and I use nRF Connect SDK v1.4.99-dev to compile the thread firmware.
I am using 52840DK, here is a screenshot of my project creation
No code...
Hello,
I had encountered framing errors when running automated tests that utilize UART CLI in my main code base. Currently what the test does is it sends a CLI command...
Hello,
I am using a nrf5340pdk board and I want to connect a sensor using I2C.
Which pin numbers of the board can be used for the SDA and SCL connection?
Do I need to...
