Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello,
We are using the nRF52 DK board and Keil uvision 5.
Using SDK 17.0.0 we can successfully load and build the `examples`. If we choose `examples/peripherals` we can...
Hello, everyone.
I would like to use LSM9DS1, a 9-axis IMU sensor. To test this, an IMU sensor module 'SparkFun 9DoF IMU Breakout - LSM9DS1' was purchased.
This module...
I am working with Zephyr version 2.4 on nRF52840-Dongle for adding ability to scan CODED PHY devices. My host is Raspberry Pi3 with kernel version 5.4.51 v7+, HCI_USB sample...
Hello,
I am trying to run USBD_MSC example using PCA10056 board from SDK15.
It works fine, when creating new file on each button press.
I modified code to create and...
Hello everyone ,
I have question about the difference between periodic message publishing via the module's configuration and publish message by a standard timer.
I notice...
nRF52833 DK i have seen from Images of board that an external antenna will be required(there is a Antenna connector on board). I am wondering if it has built-in antenna or...
Hello,
I am on nrf-sdk v1.3.0 and mwf v1.2.0.
We are updating our product to the above mentioned nrf-sfk version and have noticed that MQTT connection gets stuck after...
Hi,
I enabled flash log backend with NRF_LOG_BACKEND_FLASH_ENABLED set to 1, and NRF_LOG_BACKEND_FLASH_START_PAGE to custom address to keep it as the starting address for...
Hi,
We have successfully created a PCB layout with a PCB antenna following the reference schematic provided by the nrf8001 datasheet. We tested and it is working fine. However...
Hi,
I am trying to interface External Flash (IS25LP064A ) using SPI example in SDK v16. I am able to read the Manufacturer_ID and the device ID from the external flash....
Hi,
Is it possible to somehow read END event register via CPU (not with ppi usage)? If yes, how? I have tried to read value on address from pointer returned from function...
Hi, I am facing an issue my product contains Ble dfu update, I tested my code without enabling DFU and it runs fine ... but after enabling dfu and creating package... I update...
Hello, everyone!
I use SDK v17 and test various functions using App_Timer. The timer function that I want is to turn the LED on for 5 seconds and then turn off after 5...
Hi,
We have been working with a coordinator and an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Both devices are Zigbee 3.0 and implement...
Hello all,
I am trying to make use of some Sparkfun libraries for some sensors in my nrF52pca10040.
I am interested on I2C, these libraries use the Arduino library Wire...
