Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hello.
I have encountered a case where app_timer gets stuck indefinitely while processing its timer queue. I have attached a simplified version of the code that runs on...
Hello Nordic Team,
I have an application running on SDK 13.0 which uses the app_timer for some timeout handling and so does repeatedly call app_timer_start and app_timer_stop...
Hi, had to modify this file
SDK nRF5_SDK_15.3.0_59ac345 in file apply_old_config.h
line 818
(SPI_ENABLED && (NRFX_SPIM0_ENABLED || NRFX_SPIM1_ENABLED || NRFX_SPIM2_ENABLED...
I've been learning to use the PWM.
This should set the PWM up for a period of around 250ms
After the period is over I expect to clear pin 23.
I find that its cleared...
Hi All,
In nRF52 SDK 15.3.0 , example ble_app_uart in peripheral mode, i have changed the TX characteristics which is initially of type (notify) to type (read ). I am able...
Hi community, I have a problem establishing a connection with more than one device in the MQTT client example (MQTT/6LoWPAN/BLE). I'm using:
SDK v15.3.0 (also nRF5 SDK...
Hi,
I'm trying to connect my nRF52840 SoC to nRFgo Studio on my Windows 7 Laptop using the usb connection on the nRF52840, unable to see any data about the connected board...
Hello everyone,
I need transfer large data 12KB array send central to peripheral using nrf52832. I try this examples in central (ble_app_uart_c) and peripheral (ble_app_uart...
Hi,
I am using nrf52840 with custom board, sdk 15 and and softdevice 6.0.0. I modified saadc example to sample SAADC value once and stop it in saadc_callback. Everything...
I would like to know, what is the correct workflow with Alarms ZCL cluster?
There are no examples with it in SDK (at least, as I have seen). The documentation on this subject...
Hello,
We have started to design a project and we would like to use the Nrf52840 as border router with a linux terminal. The link would be a serial over USB. So the NRF52840...
Hi,
I'm trying to create with the S132 SD on the nRF52832 an application, that will provide 3 different kind of sensors. My goal is, that these sensors will appear as an...
Hi there, I could not find any documentation about the meaning of the version numbers, when creating bootloader settings:
nrfutil settings generate --family NRF52840 --application...
Hi
I am working on Eddystone in nRF52832. Its working fine when using power supply.Then I used Lithium battery as VDD. then it not working properly, only working in connectable...
Hi,
I was wondering what is the recommended GPS circuit would be for an always outdoor device with a large patch antenna, without the need for an amplifier. Would the following...
