hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hello Nordic / Zephyr experts,
I am looking for AT command parser for the UART of nRF52840. Want to send and receive AT commands to a LTE modem using MQTT messages. Need...
Hi,
I am aware that nrfutil does not work for OTA updating the nRF53 and was wondering if there was a similar tool that will allow me to achieve this? I need to update ...
Dear BT Mesh experts,
What's the advantage/disadvantage of using the nRF5 SDK for Mesh compared to the nRF Connect SDK ? Consider a rather simple BT Mesh device that provides...
Hi support Team,
Is there a way to make the nrf52840 to connect with only given MAC address (i.e., a MOBILE) ? The MAC address (i.e., a MOBILE) will be changed dynamically...
Hi Support Team,
What's the UBM pad diameter of nRF5340-CLAA?
BTW, any correlation between it and label 'b' in Mechanical specifications in PS?
Best regards
Sal...
When I try to open the .overlay file in SEGGER it shows me an error : "Can't Read file" with the message "Can't open xxxxxx/xxxxx/xxxx.overlay for reading.
Has anyone else...
Hi,
I am running Homekit over Thread sample(NCS/Homekit tag v1.7.0 using MTD-SED conf) on my custom board and I found that the QSPI Flash (MX25R64, as same as the one use...
I want to test OTA in button mode. I have configured the button in DFU project. Now I upload the files in my device in the following pattern:-
1)Bootloader hex file
2...
Hello,
I have an nrf5340-dk board and I am trying to play around with the different baud rates through changing the overlay file (as shown):
I am using teraterm...
Hi guys,
After weeks and weeks of trying with 3 different boards (Thingy91, nrf9160DK and Custom board), combination of different LTE Antennas, Bell, Hologram and iBasis...
I am using nrf52840's dongle development software, and I found that when the slave device sends LL_SLAVE_FEATURE_REQ , the host will return LL_UNKNOWN_RSP. I want to know...
Using the NRF connect app we can simulate the problem we have in our app Cowboy. Some customers cannot pair with the bike that uses the nRF52840. We have secure and non secure...
Hi, I am Marcous.
Currently I am doing multiple beacons (transmitters) in direction finding demos. Since I found that there is no way to simultaneously receive the CTE containing...
Hello there,
We are developing an application which inits all the peripherals and sleeps.
We are initializing:
GPIO's for waking up from interrupt
NFC also should...
Hello,
I am using NCS v1.6.0 for nRF52840.
I need to write 8210 bytes to flash via I2C. I configured the I2C0 with NRFX_TWIM and NRFX_TWIM0 enabled in the prj.conf file...
