Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
I'm trying to run Provisioner Example on my nrf52840 DK, which is in examples/provisioner directory, . First I've build softdevice on DK and then I'm trying to build provisioner...
Hey NordicSemi. In my new project, I use DK NRF9160 and I need to determine the location. Since hardware GPS does not work, I decided to use the detection of coordinates through...
Hi,
Something locks-up my I2C sometimes and I need to make I2C recovery. It looks like Nordic has not implemented the zephyr i2c_recover_bus function, so I guess I need...
I'm looking for dual core inter task communication examples
where a thread on one core is interacting with a thread on the other core ?
e.g. will there be some kind of...
Hello All,
I was looking at the Digi XBee3 modules for a ZigBee project I am working on. What is great is they allow you to write MicroPython code to control the network...
I am trying to send some values from nRF52810 Board to my Laptop. I am using a nRF52840 Bluetooth Dongle to connect the board to my laptop. I am using the "Heart Rate Collector...
Is there a way to get the values of CompanyID ProductID & VersionID before provisioning? I'm working on my android application using the nRF Mesh Library and after identification...
Hello, I work on nrf9160 dk and i try to get tx power: For exemple, with a RSRP -76 dbm i get this consommation curve (read current on P24 throught 0.5ohms resistor):
and...
Hello,
we are developing a HID slave device. we need to support five cell phones connect and bond with the device not at the same time.
we use the ble_hid_keyboard example...
Hi,
I am check this code: https://github.com/NistantriTech/ibeacon_nrf52/tree/ed938973c9a8ebd4f0bb91a3689e5d8242980681
It used SDK15.0
On Ebyte 52832 - and face problems...
Hi
After trying out nRF5340 step-by-step guide we'd like to learn nRF52833 following similar step-by-step start-up guidance if such exists.
I guess for the basic operation...
Hi all. I am using the twi_sensor example of the sdk12.3 in a NRF51822 Taking a look on the tx function: err_code = nrf_drv_twi_tx(&m_twi, MXC400_ADDR, reg, sizeof(reg), false...
Hello ,
we know that, when initialize a BLE slave device ,we need to define the BLE MAC address type.(we need to write our owen address ,not usig the original ble address...
