Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
I am starting to get up to speed on nrf_crypto, but trying to understand under what scenarios would one choose between Oberon or micro-ECC backend ?
HW = nRF52832, SDK 16...
Hi all,
I am testing the OpenThread connection with 3 nodes at the present,
One is working as End-device with MTD (Minimal Thread Device) firmware others are FTD (Full...
Hi Support Team,
In reading this white paper,Section 3.5 Testing RF performance,
a colleague informed me that a test UICC which is provided by the LTE tester vendor say...
Hi All,
I'm using hci interface to scan the ble based beacons.
While scanning hci interface's Rx bytes keep on increasing because beacons are being scanned.
I'm using...
Dear everyone,
My platform is SDK16 and IDE is KEIL V5.25.
I set timer 2 to 104uS to sample a serial data. It isn't UART data, no start bit and stop bit.The start bytes...
1. Using the nRF Connect SDK v1.2.0 development environment, nrf9160 developer, when testing connections to NRF_CLOUD in China, cannot be connected. 2. Please provide the...
1. Optimization is set to 0 flash read and write errors, set to 3 flash read and write correctly? 2. Please tell me what effect the optimization is on flash reading and writing...
Hi .
I am using nRF52840 dk in windows 10 environment.
I want to measure the RF output power of a single nRF52840 using nRF52840 dk.
I succeeded in generating a...
Hello,
On my custom board, on nrf52832, I can can use app_buttons for all usual pins, but not the XL1 (P0.00). I didn't try XL2 (not routed)
Using this pin as input or...
Hello devzone! I am using translation.
I'm trying various things in a continuation of my previous post , but I do have one question.
I set NRF_LOG_ENABLED to 0 at ble_app_blinky...
I've got an nRF52840 dev kit and am building my code using the app_ble_hrs_freertos project as a starting point. I'm building the .elf file, which I load into Ozone to do...
Hello everyone,
I hope that you are all doing well during those hard times...
I am writing a code for a nRF52840. The connection is successfully established with a cycling...
