hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
SDK 15.2
Mesh SDK 3.1.0
Base Example: Enocean_Switch
Im working on creating an LED dimming firmware that uses a long press on the Enocean remote to dim the LED. It works...
Hi there, I tested range on NRF52840 with Thread SDK, so I have got small enough range. The test has been performed indoor, power transmission 0dBm, the range result is 10m...
Hi. In our application we are reading the voltage on 3 Analog input pins via saadc. System is also a BLE central and UBD CDC device so lots going on.
Quite often the 3 analog...
We have a requirement for the ble-peripheral device that we are designing to be able to be "registered" to a user through their iphone. If that user has multiple iOS devices...
I would like to insert some asserts in my code to ensure that code is not running inside a interrupt handler, because this can cause hard to debug issues.
How can I check...
Hi,
I tried to program the Thingy52 with the node and bridge to set a Mesh and I got the message in red you can see at the attached.
Please advise.
Thanks
Hi,
After reading the nRF24L01 documentation, I have some questions regarding page 66 of the documentation ( https://infocenter.nordicsemi.com/pdf/nRF24L01P_PS_v1.0.pdf...
Hello,
Has anybody achieved to perform Mesh DFU over serial on a Raspberry Pi using nrfutil?
I can successfully perform it on Windows 7/10 (intel) so far with no problems...
Hi All,
I am running a modified example of the 'ble_app_multilink_central_pca10056_s140' project.... I am running this on a PCA10059 dongle. The project connects fine to...
I am getting following error while building the project.
undefined reference to `nrf_drv_timer_pause'
undefined reference to `nrf_drv_timer_clear'
I believe these...
I have uploaded the AT CLIENT firmware and I have connected my nRF9160 dk to my apn, but I don't find any type of AT commend to set a socket and open a port to send and receive...
Hi,
If fires multiple generic_onoff_client set LED = True command from PyACI libraries with Ack = True to multiple nodes, the generic_onoff_client will provide a "generic_on_off_status_handler...
Hi sir,
I want to know if nRF9160 is programmable or not, like other wireless microcontrollers i.e nRF51/52 and ESP32 etc.
If it is programmable, where can we find the...
Hi,
Can we do DFU-OTA on nRF52810 controller ? why i am asking this is , when i saw a video about DFU-OTA they saying that only the controller having at least 32 kB RAM...