hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hello, It is my first time running FreeRTOS on NRF52 and I would really appreciate any help to figure out the root cause for the hard fault. I run a simple FreeRTOS application...
nRF52832_XXAA, S132 v5.0.1, SDK 14.0.0
We enable SoftDevice via nrf_sdh_enable_request(). We immediately assert nrf_sdh_is_enabled() so we know it worked. On the first...
I recently got a custom board manufactured using an NRF52840 with the TI AN043 antenna to find that everything worked except for the bluetooth antenna. So I'm here to seek...
Hi,
I was able to successfully complete Figure 2 on page 6 of nRF_Sniffer_UG_v2.2.pdf, and successfully loaded and ran sniffer_pca10028_1c2a221.hex.
I rebooted my computer...
Hi,
We’d like to migrate from nRF51822 to nRF52 series. We have 2 targets : nRF52811 and nRF52832. We’d rather use nRF52811 (better sensitivity, lower consumption, features...
Hello
I'm trying to send an uint16_t array with 750 elements over the NUS service.
To do so I fill the data in multiplle uint_8 arrays of length "m_ble_nus_max_data_len...
Hi All,
I've got an nRF 52840 PDK and I'm connecting a GPS module ( Adafruit Ultimate GPS Logger Shield ) to it to read the data using nrf_serial.h library. I get about...
Hi
I am working on a project that has two timers, TIMER3 and TIMER4 (TIMER3 as timer and theTIMER4 as a counter). TIMER3 resets after counting up to 4. I am using PPI to...
Hello Nordic Team,
I was working on blinky_systick Example(Path - nRF5_SDK_15.3.0_59ac345\examples\peripheral\blinky_systick\pca10056\blank\ses)which is available for...
hi...
i am using mesh 3.1 latest version , i have changed the light switch example code , where i am sending the character . i have completed the scanning , provisioning...
Hey. I'm looking for a complete free RTOS for the commercial development of our startup. We will use the SEGGER Embedded Studio IDE and SoC Nordic nRF52840. As I understand...
Hi,
i'm current working on example light switch, when i use function generic_onoff_client_get(); in client to get status from server, callback function app_generic_onoff_client_status_cb...
We're running a multi-drop single duplex RS485 bus, so it's important to stop driving the bus as soon as a transmit is complete so the next device can transmit without two...
We're running a multi-drop single duplex RS485 bus, so it's important to stop driving the bus as soon as a transmit is complete so the next device can transmit without two...
