Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Hi,
We are using 52832 to developing.We need DSP to finish the arithmetic.
Can you tell me how to use the DSP on 52832 ? Do you have same examples?
These algorithms...
I have an nRF52 dev board and I'm trying to build and download some of the example programs.
The example files were downloaded using the Pack Installer in Keil MDK-Lite....
Is there any way that can allow the user to advertise a sine wave for example over a specific channel or over the three Radio channels ?
I am using S130 and Nordic SDK 8...
Hello,
As a summary (described fully below) I have loaded the ble_app_hrs example onto my device and its not working right as LEDs that should light up don't and the program...
In some of the Nordic examples I found by viewing the raw advertisements that the company ID is set to Nordic's ID (0x0059). In order to communicate with Apple devices (e...
Hi Nordic Support community,
I asking regarding LNP, Location and Navigation Profile, if it's possible to on top of nordic products? If so like which ones ?
There's barely...
Reading the documentation Address config it is clear how to use RXADDRESSES, could you please explain how to use TXADDRESS ?
As of TXADDRESS there are 3 bits available...
I am having trouble with using shockburst (based on microesb from github) after disabling S132.
When I use microesb with no SD, i just do nrf_drv_clock_init(), start lfclk...
Hi,
I am new to Nordic development platform and am exploring ways to develop software applications to communicate over bluetooth. Presently, I am working with NRF51422...
Hi, I have a problem about gpiote interrrupt.I have set two ports to detect the external interrupt(low to high). If only one port get active ,it works fine. But if one port...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi I am beginner to nordic ble. I have four nrf528** development kit. I am just trying demo heart rate example with android toolbox app. Suddenly one of my nrf devlopment...
I am currently using MBR, and know the general interrupt latency due to MBR + SD from Table 26. But I cannot understand how you arrived at those numbers. IF this table was...
Hello All
Hi, I use nRF52832 with SDK11 Version. But SDK11 didn't provide any CSCS central example. Anybody wrote ble_cscs_c.c for BLE / Cycling Speed and Cadence Service...
