I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hello, I am using SES ARM V7.32 and SDK is 17.1.0.
I am trying to test the ble_app_uart example, but Build failed keeps occurring.
There are no other error comments, so...
Hi Everyone,
I am trying to develop a simple application with the XIAO BLE Sense device, the idea is to send a BLE message when something hits the device. To achieve this...
Hello All,
I am using the nRF54L15-DK and the nRF Connect SDK v2.8.0 with the Zigbee-Addon.
Is the maximum TxPower value that can be set for Zigbee 8 dBm?
Best regards...
Hello.
I am developing using nRF5340DK and nRF Connect SDK v2.9.0. I am checking the operation of "Scheduler Server". The action was executed, and the date and time are...
Hello. Using the Zigbee messaging cluster, we are writing code for data exchange between ZR and ZED. (Based on the Zigbee example light_bulb/light_switch/light_coordinator...
Hello,
I have a custom board which has an nrf5340 on it. We are using nRF Connect/Zephyr in this project. Currently the board has a pretty simple interface seen in my overlay...
I am currently developing a PC application for Bluetooth data reception and chart display. I want to perform secondary development on pc-nrfconnect-ble. My current development...
I'm using SDK15.3 on an nRF52840 with FreeRTOS and specifically non-preemptive scheduling.
I want to so some transfers on SPIM (it's configure with DMA but that's not a...
My project uses a PDM microphone connected to a nrf5340. I previousy had this working using the nrfx_pdm driver, with NCS 2.6 but then had to migrate the project to NCS 2...
There is usually a panel for application where you can see / delete or add build configurations, as shown in the enclosed picture. The panel on my vs code installation has...
Hello,
i am debugging issue in our device. I ported the nrf5340 Audio application to our custom board and modified it for our use. We use audio broadcast mode.
Device...
HI,
I am developing a ble mesh application on SDK 17.2, I enable Instaburst for support long mesh message(more than 300 byte), it worked well.
Now I changed to the nRF...
Dear Support Team,
I'm trying to develop a mouse using Pixart's PAW3395 sensor. I've written functions for reading and writing data through the SPI interface. I took help...
I didnt see in the data sheet a specific window of time the chip needs to properly shutdown without interrupting a critical process that might cause corrupted memory. I am...
