Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello Experts,
I my main.c, I have defined my own TIMER1_IRQHandler() and when I build the code I get the error
Rebuilding 'timer_pca10100' from solution 'timer_pca10100...
i use ble_app_uart example code.
i have some problem that sometimes MCU can send data to application. but sometimes MCU can't..
ex) Success : 0x01 0x02 0x03 0x04 0x05...
hello i'm using nrf52840 dk board for communication with windows pc.
in nrf 52840 datasheet usb max speed is 12Mbps but my project based on "usb_cdc_acm" usb speed is 4Mbps...
Hi, we have project AoA direction finding. Firstly we have nrf5340 dk kits. Also CoreHW ANT3 2x2 matrix antenna kit. I run the direction finding connectionless demo on nrf5340...
Hi,
I am working with USB mass storage example from the SDK, and it works perfectly with the DK. Now I am working on my integrated PCB, and the same mass example doesn't...
Hi,
I am trying to get both the 802.15.4 stack and the BLE AoA stacks to run concurrently on an nRF52833.
Looking at the documentation here , it appears that it should...
Dear Sir/Madam,
I am trying to enable FEM support on zigbee/light bulb, and want to SKY66112-11 FEM working on Receive bypass mode. I set all pins at proper setting at initialzation...
When performing DFU with the same Android device + nRF Connect on the same target device, the speed becomes significantly slower on Android 15.
The attached image captures...
Hello. The visual study code uses toolchain v2.7.0, SDK v2.7.0 I'm trying to test the saadc example (in modules/hal/nordic/nrfx/samples/src/nrfx_saadc/) in "creat a new application...
Hello Nordic Team,
Our existing device using NRF52840 QIAA, we are plan to replace the QIAA package with CKAA package for size reduction. After I went through the SPEC,...
I´m testing the nPM1300 in a custom circuit with Zephyr on an nRF52 / nRF53 attached to it. It looks like the IC isn´t charging a battery. For testing I use the nPM1300-EK...
Hello,
Can I use in production nrf52840-DK as programmer to program E73-2G4M08S1C module on custom PCB?
What should I do to make the program code unreadable?
Hello, I need further assistance with the issue in the mentioned ticket ID, as it was closed by mistake. Could someone please reopen it so I can continue the discussion? ...
nRF52833-based board, software is based on Zephyr and Nordic SDK 2.1.2. Using Tag 2 type driver library, nfc_t2t Occasionally, when NFC coil is tapped, we observe one of the...
