I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi everyone,
I'm quite new to the Nrf Connect SDK and Zephyr.
I'm trying to implement a simple DFU (over UART) bootloader. The idea is that when the microcontroller powers...
Hi,
I have encountered a challenge with the nRF54L15 that I am hoping someone might know a solution for!
My device has a power enable pin (on GPIO1) that must ideally...
Hi
This isn't about a problem so I'm not sure if this is an inappropriate post to make here, if so please feel free to remove it, however there is no commercial incentive...
Hello everyone.
Absolute novice here but a lot of reading over the last few days has brought me here.
I'm currently watching a little robotic project being developed....
Hi
We have developed a remote-control system where both the sender and receiver are built around nRF52840. Today, the SDK is sdk-17.1.0. We are now considering moving over...
The Nordic Hardware Design Guidelines suggest a 0.050 mm soldermask clearance around the pads which should give a 0.100 soldermask sliver between the pads according to the...
Hello all,
Currently I am working on getting the nRF Mesh DFU target and distributor samples working in the context of our project. This appears to have been successful...
Hello,
I have been chasing this problem for some time, but it has been difficult to capture.
The issue occurs when the device is sitting idle (no eDRX or other power-saving...
Hi,
I'm evaluating Wi-Fi NAN (Neighbor Awareness Networking / Wi-Fi Aware) for a project and came across the nRF70 Series, so I wanted to check on the current status and...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Hi
I'm building firmware for the nRF54LM20A running USB HID + ESB at 8 kHz. Currently I am referring to the nRF Desktop ( nrf_desktop ) sample as a reference. But there...
We have thousands of devices live in production and we sometimes encounter the situation that we cannot restart bluetooth advertising anymore after a connection attempt. ...
Hi
We are using the nRF52840-QIAA-R in a lot of PCBA, now I see there is a new revision nRF52840-QIAA-F-R and the old type is not recommended for new design.
What is the...
Hello! Sought out to upgrade from NRF SDK 3.1.1 to 3.4.0 today so downloaded and installed it on Mac using nrfutil sdk-manager command line, and that was fine. The project...
Hi,
In our PCB using the nRF54L15, we used different P2 pins for the sQSPI, believing after reading the docs and driver API, that one could configure different pins than...
