Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I am evaluating a thingy:91 for an asset tracker project, so far a fantastic device. I followed the getting started guide and different online videos.
I have never been...
Hello all,
I am using sdk 16, trying to make a simple interrupt from pin 19.. I keep getting error code :- on this line nrfx_gpiote_in_init(19, &in_config, in_pin_handler...
Hello,
I decided to update the SDK from version 1.9.1 to version 2.2.0 but I countered the following issue:
Could be oldest compiler path?
Thank you in advance....
I've developing an application for the nRF52833 that uses the v7.2.0 s140 Soft Device and the secure BLE DFU bootloader.
I'm able to compile the bootloader (taken from...
Walkie-Talkie example works (add CONFIG_WALKIE_TALKIE_DEMO=y to prj.conf), but it is not bidirectional. I can only hear sounds from gateway's OB microphone.
I also tried...
Hello, I'm trying to get an analog comparator working on the nrf52833DK. I am using NRF Connect SDK version 2.2.0. I have the following code:
At the moment when I would...
I've set my Board Roots variable:
The folder specified is root to my board definitions:
I've closed out VS Code and restarted it a couple of times. However, it refuses...
I cannot find anywhere how to make a physical connection from the nRF5340 to the PC in order to enable logging from the uart. There is information on baud rates etc, but I...
Hello!
I am working with a BLE central device running on an nrf52832 using the S132 softdevice and sdk version 15.2.0
I need to pull the full device name out of the scan...
Hello,
This is the first try to connect the new nRF52840DK on MacBook pro with macOS Monterey with Intel core i7.
I've followed the steps
Install nRF Connect for...
hi,
i am testing the ble_app_blinky_c_pca10056 code for the nrf52840 dongle , i changed the board from Pca10056 to pca10059 by following the instruction given in the
...
Hello
I built the NFC record_launch_app sample from nrf\samples\nfc but it crashes before it gets to main on my nRF52840 DK
I don't see any printk messages at all in the...
Hi,
Have an issue which has popped up with our application. It is configured to use buttonless DFU for OTA updates.
It's been working fine in the past but with a recent...
I've been using the nRF9160 modem library for my implementation. Up until recently, I've had no problem with the interface. I've been using SDK v1.9.1. I decided to update...