hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
I made an assumption that the nRF52840 Dongle has the ability to communicate via UART as most boards I worked with have this feature. This seems not to be true, but I don...
HI all,
I've found that adding a 10uF capacitor to the 52805 beacon reduces the power consumption, especially after speeding up the broadcast interval (100ms broadcast interval...
Hi
1. How to set PWM power-on state to Low level in ncs v2.4.1 2. How to configure the dts file so that the corresponding I/O port is in the low state when PWM is powered...
Hello,
I am after an example for nRF5340 showing how to use RTC to wake up from sleep.
I have a couple of timers running few tasks at regular intervals in a forever loop...
new to nordic and keil need help compiling custom project
currently my main file only works with the nordic 1822 series processor and in your example.
I need to have it...
I cannot find a specification for the SAADC converter's reference accuracy. The product specification indicates it is 0.6V, but beyond that I cannot find anything. Looking...
Can we run our Customised Bluetooth Host Stack on nRF5340.
Please provide us with sample Brinup Code for Bluetooth Controller.. Send HCI Reset and Bringing up the Controller...
We need to retrieve data from an FPGA to the nRF5340, process it with the network and Wi-Fi protocol stacks and then send the data to the nRF7002 for Wi-Fi transmission. We...
Hello, I am wondering - Is it possible to program BL651 Bluetooth 5 with nRF52810 using pca10040 development board with nRF52832 on it and using
BLE HID Keyboard and Mouse...
Hi!
Currently I have the following application requirements:
Use SPI peripheral to communication with FPGA device. ( NRF5340 [ SLAVE ] <---> FPGA [ MASTER ] )
The goal...
i'm trying to read voltage signals from a sensor using internal ADC.When the input is not connected,there will be noise. I use differential input pins like this:
NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_DIFFERENTIAL...
Hi,
i need to store few configuration bytes in non volatile memory. I found out there is settings module that can be enabled in Kconfig GUI (SETTINGS option).
My use is...
Hi,
I have successfully programmed the nRF5340 Audio DK as a gateway device using the Command Line Tools and by using the directives listed in the 'nRF5340 Audio' program...
I'm working on adapting ST's RFAL NFC library for ST25R3916B/X-NUCLEO-NFC08A1 on an nRF5340/DK in order to emulate an NFC tag, and have run into an inconsistency I'm hoping...
I have an application where I need to trigger time critical SPI reads of accelerometer data (sample rate is very crucial and data is fed into a FFT). In my current SDK based...