Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
develop tool is nrf5340dk and sample peripheral_uart in NCS1.5.0 ,when debugging , function uart_cb() alway run in case UART_RX_DISABLED and case UART_RX_BUF_RELEASED
,code...
Hello,
I am developing a product using nRF52840 and BLE communication of my product uses NUS.
SD: s140_nRF52_v7.0.1
SDK: nRF5_v16.0.0
Recently, I want to encrypt...
I am using a nRF52840 with " SEGGER Embedded Studio for ARM 5.10a" and " nRF5_SDK_17.0.0_9d13099 " sdk.
I am enabling a interrupt on a GPIOTE pin using this code.
I...
Hi,
I need to store some "XML" data in a buffer, to send over serial.
I have some trouble with storing this variable, due to some symbols.
char N_Pos0[150] = "<txid...
Hi,
I've had a product that's been out there for years. In it, we call `sd_ble_gattc_primary_services_discover` a few milliseconds after we've received `BLE_GAP_EVT_CONNECTED...
We would like to try using the standard DFU process to update third party ECU connected to the nrf52 chip. Our idea is to modify the standard DFU zip package - to add a new...
https://www.novelbits.io/bluetooth-5-advertisements/ i have followed this. want to know in simple words how periodic adv is helpful in contrast to simple advertising
The Attach LTE is working but i can't use some command AT for testing Data, as you can see in the screenshot below, i tried with somes commands but it's failing, can you please...
I think the figure 10 in nRF9160_PS_v2.0.pdf chapter 5.1.3.1 is worng.
R and C should be swapped.
It is different to Figure 118 chapter 10.3.1 R2, C10.
Exist a list...
Hello,
I have the following problem. I am using the SDK for Mesh 4.2.0 with the nRF5 SDK 16.0.0 on the nRF52840 DK, I am using the sensor model and I have extended it with...
Hi,
I want to make a BLE Multirole application where the central demands LESC, bonding and MITM and peripheral connections is JUST WORKS bonding.
Is that possible? If...
I'm trying to modify the flash_fds example to write a start time when a button is pressed, then an end time when the button is released. I get the time over TWI from an RTC...
Hi, We are into Commercial health devices using nrf5340 and looking to use AoD technology for our device to get its indoor location. We need to have a Receiver with antenna...
What are different options to load the soft device on custom board? Currently, I am using nRFGoStudio to load the softdevice on nRF52840 DK. We will not have segger hardware...
