Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi
We are using the nRF52832 chip in a design and try to reduce the cost for the product. I have some ideas to simplify the circuits but have some questions about the capabilities...
After clicking on Raw Data in Nrf connect App I am getting this 0x0201041AFF590000150112233445566778899AABBCCDDEEFF0FFFFFFFFC3. what are 0201041AFF these bytes ? can I remove...
Hi
There is a lot of sleep mode at 5.2.1.1
Could you explain what the different between "ION_RAMON_EVENT", "ION_RAMON_POF", "ION_RAMON_GPIOTE", and "ION_RAMON_GPIOTEPORT...
Hi,
I just added some more data to my iBasis SIM card, but I can't seem to find the receipt for the purchase. Where would I find the receipt for this purchase?
Thank...
Hi there,
I have a few questions regarding the Development Kit hardware design. I just bought up the polygon pour manager. I noticed that all layers except Mid-Layer 2 are...
In the documentation, its suggested that the antenna should have a matching network between the WLCSP NRF52832 and the 50 ohm transmission line that looks like this:
...
Hi Team,
I am working on SYSTEM ON mode with Low power mode also called Idle mode in nRF9160 module.
I was able to go to Idle mode with current consumption of 6uA with...
Hello there,
I created a project a while ago with the SES and the SDK 15.x. For a new Project, we would like to move to PlatformIO. Right now I am evaluating where we will...
Hi Guys
I recently made my own PCB for a project. On the PCB I am using a Laird BL654PA Module with external antenna. All the I/O's work great but im struggling with the...
Hi,
We had met problem at buttonless DFU with bonded information at Andriod set-top-box.
The problem we saw is we can not know when the ATT table is different at andriod...
I'm trying to wait on a single POLLIN event on a net socket, but I'm finding that poll() will still return immediately with the POLLIN event even if it's not set in the struct...
Hi , I am developing a zigbee project using nrf52840 using NRF52 zigbee sdk . I had to do some changes in zboss header files ( zb_config_common.h and zb_config.h ) to change...
I'm using the NRF52840-DK with the SB40 jumper cut, then powering through P21 and measuring with an ammeter across P22. USB is unplugged during measurement. I'm using zephyr...
Hi,
Eventhough I am able to communicate with my I2C slave, this message appear for every transmision.
[00:00:00.709,350]
[1;31m<err> i2c_nrfx_twim: Error 195952641...