Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
The objective is to have a device which constantly advertises some status information - this must be always visible to any Central in range.
The device may connect to at...
I inherited an active project with regrettably little support from the previous developer.
I have been trying to download a copy of the application firmware that I generated...
I try, DFU by USB-SERIAL on NRF52840-DK. I installed SoftDevice S140 V6.1.1 and open_bootloader/pca10056_usb (SDK15.3) Python2.7.16/nrfutil for windows was installed. My DFU...
I am trying to keep an output pin asserted while I jump to the DFU on the 52840.
We have a dead-man switch hooked up to pin 19. I need to hold this pin high while I jump...
So we are using NCPTransport from nrf-util (nordicsemi/thread/tncp.py) to have CoAP connectivity over Thread NCP from Raspberry Pi to other Thread devices. We have a use case...
Hi,
I am trying to install pc-ble-driver-py pypi lib into custom yocto setup. I have created recipes for it which is shown bellow
in python-pc-ble-driver-py.inc
...
Hi. Im working with an application that uses the s110 softdevice and i want to use the s130 to be able to recive advertisereports but when using the s130 Everything stops...
Hey everyone,
I've got an nRF52840 DK on my hands. There's an interesting crash occurring when the return value from ble_nus_data_send() is passed to APP_ERROR_CHECK()....
I am using several Laird BL652 units on a project. They contain a nRF52832. For the most part they are working great, except I have one that only works some of the time and...
I have been trying to use the new GPS example, however, I could not get any location from it yet. It seems that after 30 tries, it stops working (time-out problem). Should...
Hi all,
I'm starting developping code with SES, on an nRF52810 (192kB of Flash), with the BLE stack S112.
Because my project include BLE and custom UUID, I started with...
Hi
I am using the nrf53832 dk.
In the nus example once the data is received from the phone(central) I want to write this data to the flash. I referred to the fstorage...
Hi everyone,
We are currently working on a BLE border router with a module based on nrf52840. The custom board has a MAC + PHY ethernet controller that communicates with...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have gone through below...