Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
My Setup: -> OpenWRT Chaos Calmer 15.05.1 -> Kernel - 3.18.23 -> MCU - nRF52832 Custom Board -> SDK - 15.0.0 -> IDE - Segger Embedded Studio
I am able to start a 6lowpan...
Hello,
I would like to know from were i can get release history for Nordic device family pack.
I can find Zip file for downloading different Nordic family packs but wit...
We want to support low power end device sleepy so do the MESH SDK 2.0.1 has the support of Friend and low power mode support in mesh SDK? I'm using nRF51822 SoC .
How are multiple messages to the same device/group/broadcast managed in Mesh?
I have a system where two switches control single light bulb. If both the switches try to turn...
Hi,
I am new in BLE.
Can anybody please explain me, how does tx_power_service works.
And how does it calculates the RSSI value.
Thanks in advance.
Varun
I am now based on nrf52832 SDK14.2 development, as a slave, when nrf52832 and mobile phone Bluetooth link, I want to know the current connection interval, how can I obtain...
I am interfacing LIS2DH with nrf51822. I am using 12.3.0 SDK and 130 V2 for development. I have successfully interfaced LIS2DH eval board with Nrf51822 eval board (waveshare...
I am using this flash data storage as reference github.com/.../nRF52-fds-example
Running fds_test_write() below, it writes to a file specified by FILE_ID, REC_KEY but to...
I recently got the Power Profiling Kit set up with the Power Profile 2.0.0 desktop software on OSX to measure current of my custom board. Sleep current for the whole board...
Hi,
In one of my application for Bluetooth 5.0 i would like to use nRF52840. Product requires certification. I would like to use MCU which has BLE on chip and certified...
Hi,
I'm using nrf523810. The current consumption that I get for proximity is 4mA and I want to reduce it to less than 1mA. I use the proximity example nrf5 sdk v14 and v15...
The computer and the 52832 are connected through a serial port. I want to send 2Kb data to my computer. But my computer can only receive 256b data. What should I do?
Hello,
I'm currently using the light switch proxy example with 3 server proxy, 1 client proxy and 1 provisionner.
The example is currently working but I don't understand...
Hi,
I have a question regarding the width of the RF traces on the NRF24L01+. From the gerbers I notice the width is approximately 0.5mm and the separation to the closest...
Hi every one.
I have issue that: our board production have NRF24L01+ IC not good, so we need replace them by new IC.
But we dont have enough NRF24L01+ IC, we have NRF24L01...
