hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Has anyone tried porting over on of the FreeRTOS examples for the nrf52 sdk onto the Thingy?
I see that it has the port in external/sdk13/external/freertos, but don't see...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
Hi!
I've found mismatch between schematic reference from Product spec ( here , page 692) and PCA10056 PCB (Preview Development Kit) for same operational mode.
In specification...
Hello,
i am using the Nrf52,
i am facing problem on the following line
#define MESH_SERVICE_BASE_UUID128 0x23, 0xD1, 0xBC, 0xEA, 0x5F, 0x78, 0x23, 0x15, 0xDE,
0xEF...
Hello DevZone community,
Currently I am using nrf51822.
Could you guys please tell me how to enable code protection besides check the "Lock entire chip from readback" in...
Dear All, Please update me if is it possible nRF52810 is having capability for SIG Mesh or Mesh Network? Also is to possible to establish Mesh network beetween nRF52810 as...
Hi All,
We received a new design with a nRF52 powered at 1.8V. We are using a JLINK probe with the SW protocol for the burnin code.
When we apply 1.8V we can’t program...
The function find_adv_name() found multiple time in BLE central examples is using the global variable m_target_periph_name instead of the parameter name_to_find . There is...
heelo every one ,
i want to use bluetooth to connect my nrf51822 to my smartphone can anyone help me because i don't have any idea there is any example ready to use pl...
nrf52832dk pca 10040 board
besides ports bits and dir setup and baudrate, etc ...
this is part of my uarte init funct (pDev = 0x40002000)
pDev->TXD.PTR = (uint) TxBuf...
nrf52832dk pca 10040 board
besides ports bits and dir setup and baudrate, etc ...
this is part of my uarte init funct (pDev = 0x40002000)
pDev->TXD.PTR = (uint) TxBuf...
I just bought a nrf51 dk to master this wonderful SoC series.
For now I intend to keep my research and studies with Bluetooth 4.1, but would like to prepare for a jump...
Will uarte interrupt call NRF_LOG_INFO, will run away the possibility of the processor? backend uses RTT
I set uarte receive dma buffer to 10, then the sender to use the...
