Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
I have an interrupt coming in every 50-150 microsecs and I want to measure these intervals as precisely as possible.
I tried this with SDK12.2:
APP_TIMER_INIT(0, 5,...
We're trying to bit-bang SWD to program an nRF52832, and we're running into some problems getting the nRF52 to respond. One theory is we're not generating a high enough clock...
i just purchased the www.xcluma.com/bluetooth-4-0-module-NRF51822-2-4G-module-development-board-ble-4-0 this xcluma nrf51822 module , so how can i progarmme it . which IDE...
Hello,
I've noticed the following sentence in s132_nrf52_3.x.x release notes:
"Synthesized low frequency clock source is not tested or intended for use with the BLE...
I'm following the tutorial in the NRF52840 SDK on setting up a Thread Border Router here and I've run into some issues during testing. For one, I'm trying to resolve ipv4...
Hi,
I'm able to successfully enable Access Port protection, either using nrfjprog or by setting NRF_UICR->APPROTECT register to 0xFFFFFF00 in code.
But I have a problem...
Hello,
Since this seems to be a very hard topic to find info about (its very contradictory and confuse) I'd like to ask a Nordic employee directly.
I'm planning to build...
This concept keeps popping up when I'm dealing with mesh networking.
My guess is that, to avoid air collision, packets/pdus are sent on a randomized or predefined combination...
Hi,
I am using ble_app_uart for my development, in that I have buffer size of 2kB which will store all the incoming data and the data will be processed and send over NUS...
Hi all,
I am using an NRF52 and SDK 13.0
I have an external device (central) that I am connecting to using my (peripheral) device.
My peer manager set up is
#define...
Hello All,
I've got two Rigado development boards that I'm programming with KEIL uvision 5. I've tried a few examples, for example: blinky, which program and work fine...
Hello
I want to clarify the exact meaning of the carrier test or unmodulated signal in DTM.
In carrier test mode, DUT transmits 0xFFF....FFF which means all one pattern...
Hello,
For my project I need to measure the battery voltage while transmitting data to get a good indication of the battery capacity. I've found an old example ( link text...
