I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Hello I have been able to run the lvgl sample in the nrf9160dk, however this only works when built in a secure board, when build in non secure a bus fault occurs. Using the...
All of our wireless products over the past 10 years have used the nRF24L01 or nRF24L01+. In order to minimize latency for our time-critical communications protocol, we are...
Hello,
I am trying to program an nRF9160 chip using pynrfjprog v10.15.2 and JLinkARM.dll version: 6.88 with a Segger Flasher Compact. This flasher supportd the nRF9160...
Hi,
I need to know on how to work with asynchronous SPI for my application use case evaluation, However i found no sample/example projects demonstrating the use of nCS...
Would it be possible to know a little bit more about the onboard integrated RF52-DK Nordic Board Antenna please? What type of implementation is used?
Kind Regards,
Za...
There is another case, where someone else pointed out the same issue but I can not find it. Anyway there was no solution.
When using VSCode with NRF Connect SDK installed...
Hi
can you help with this? Setup: MoSh example running on nRF9160DK
There appears to be some sporadic «Old AT event handler : %CESQ xx,y,zz,n » notifications with the...
Hi, I am working with the Thingy91 development board. Currently, I have flashed SLM on nRF91 and I am using nrf52 as my "main" processor for sending at commands to nrf91....
Hello Nordic
We have a device, working on nrf52832, with s132 and nRF5 sdk11.0.0, at customers around the world.
It contains a bootloader mechanism that copies a received...
Hi,
I am not able to use the gpio pin p0.18 as a gpio with nrf connect sdk.
I have tried to toggle the pin using "gpio_pin_toggle" and gpio_pin_set" functions but...
Hello, I am trying to make a connection between NRF52832 and ESP32-S Module using BLE.
I implement a simple client application to ESP32-S and I can handle read,write and...
Dear Nordic team,
considering our error analysis, does the nRF52840-CKKA-F have an internal error flag that is set when the external LFCLK source is absent or shortcut?...
Evaluating nRF53 PDK. Trying to build basic samples from zephyr repo as advised here - https://devzone.nordicsemi.com/f/nordic-q-a/54451/nrf5340-support-in-nrf-connect-sdk...
Hello,
maybe it is a very simple question but I didn't figured out the answer yet. Is it possible to start MCUboot from the application firmware code (to avoid pressing...
I have 20 advertisers. I have nrf sniffer hex flashed in one nrf dev kit and i am using wireshark.
I intend tht sniffer should scan only those device whose address i will...
