Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
The Master Control Panel will be able to keep the connection for hours and hours.
But when I am using the iPhone 6 to do the test, after connected, it will also be disconnected...
Hello
I've been having some strange problems with my SPI and TWI bus. In my setup, I'm using SPI0 and TWI1. I noticed that, even though I'm not using it, that SPI1 was...
This seems to be a common problem after searching in this forum. In my case, I need to read from an I2C slave and send the data out in BLE. I have made it work without SoftDevice...
Hello!
In my application, I have to receive UART signals from another device. The problem is the signal comes inverted so the nrf51422 can't handle it. I thought in 2 possibilities...
In spi_master.h SPI_DEFAULT_TX_BYTE is define as 0x00.
This value will be used when sending dummy clocks, or just reading from SPI slave, or writing length is less than the...
Is there a migration guide from 8.0.0 to 8.1.0? A lot has changed in GPIOTE and I can't make sense of it.
For example, should I be linking against app_gpiote.c , nrf_drv_gpiote...
I am new to BLE but have been reading up about it. My understanding is that developing BLE custom GATT profiles is similar to SPP but the difference is that BLE is extremely...
Hi,
I just started developing with nRF51DK, tested some working examples to figure the basic things out (Blinky, UART, etc).
I can't figure out how to make the multilink...
Hello,
I ordered some modules and expected them to be based on revision 2 nRF51822.. But they use Revision 1. Now I am struggling getting my Code from the nRF51-DK to work...
Hi
I am writing an application that requires bonding/paring stuffs and face a problem as below
The maximum bonds that my device can manage is 2. When these 2 slots are...
Hi
I use nRF6310 and PCA10005 to develop BLE project. When entering DTM tab, I cannot find the motherboard on "set up on".
DTM.jpg
My hardware is:
motherboard: nRF6310...
