Hi. I'm trying to write a simple MQTT app. I am consistently getting these KConfig errors to do with variables I'm not using, and I have tried to set CMake to ignore these...
Good day,
I've developed a board with a MDBT50Q on it. I'm using the Reg0 DC/DC and LDO Mode Disabled reference circuit ( https://www.raytac.com/download/index.php?index_id...
Hi,
I have the issue that my Zigbee device reports the error "Production configuration is not present or invalid (status: -1)". I followed the guide from this( https://docs...
Hi,
I am using an nRF52840 as a Zigbee NCP. I have built the firmware myself using nRF Connect, and I am also running MCUBoot. Sometimes after some usage, the chip starts...
Hello everyone,
I am testing out I2C on the nRF54L15 for a custom PCB project.
I first tested a simple mpu6050 sensor on &i2c21 on pins P1.11 for SCL and P1.12 for SDA...
I have a bit of an unusual use case where the nPM1300 is quite ideal but need to use an external charger for the battery instead of the internal charger. The nPM1300 fuel...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
Dear All,
In my application I need to switch on and off the modem using AT+CFUN=0 and AT+CFUN=4 respectivelly. My question is the following. Let's assume that the device...
SDK:V15
chip:52832
development kit:window+keil
In stm32,inder to use uart rx with DMA, we could easily use:uart Idle interrupt+dma.but how in 52832 while how many...
I’m looking at this example:
https://github.com/NordicPlayground/nrf5-calendar-example
which uses standard C function localtime(), but can not find neither in the example...
Hi devzone,
I learnt DFU through USB by performing the following steps:
1. build and run "secure bootloader usb" project with segger through J-link port J2.
2. flash...
I'm setting up a new project (solution?) for the nRF52-DK, using SEGGER, based on one of the examples in the SDK, and would like to put it under version control (Github, etc...
Hello , I m working on project to commande sim868 by serial (send AT Commands), so for the fisrt i would like to test the serial connection with an arduino to see what it...
We have developed our application on a custom prototype board with a nrf52832 (laird BL652) and it works great. We got in our production boards and all the IOs on the processor...
I have a problem while provisioning the dongles in a mesh network, which is faced by most of the people around. Right now I'm using the latest mesh sdk. Can you help me with...
I'm having trouble reading value from ADC. What I want is to read a sample and not set any timer, since I want to run it inside a timer itself and have the refreshed value...
I have designed a custom board using nRF52832. As per my understanding, we can configure any GPIO pin for UART communication. However, I am not able to configure the board...
Hello,
I am running into an issue attempting to add certificates to the device in order to facilitate HTTPS calls to our backend directly from the device.
Before the LTE...
Hi all,
I am trying make some temperature sensor with Segger and nRF52 based on Mesh BLE v4.0.
Currently I am researching documentation and examples to pick best solution...
I'm trying to use the information from this devpost: https://devzone.nordicsemi.com/f/nordic-q-a/39629/how-to-send-data-to-all-node-over-mesh
However, my remaining questions...
I would like to see an example or documentation about how to set my nRF52 DK into various sleep modes. I know that calling "sd_power_system_off()" will turn the device into...
Hello how are you?
I don't speak English very well but I have a doubt about using mesh and nfc simultaneously.
I'm using the Nordic-Thingy52-mesh-demo example - (Nordic...
