I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi All,
I have to implement an I2C Slave on my nrf52833 BLE project which is currently working (SDK 2.9.2)
I need some confirmation with the following step:
I have...
I am using the 54l10 chip, and after compiling the project, I will receive a hex firmware and a zip update package. The bin firmware and hex firmware in this update package...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
I am using power profiler from my MAC pro, to test my 51822 DK. And I got following errors:
Error while setting up device 000000123456: No firmware defined for selected...
Hello,
I am using nrf52840 dk and ses. I have written the code for hcsr04 ultrasonic sensor and I getting proper values but I want to send this data over bluetooth and I...
This is a very simple question:
According to the documentation, each dongle is assigned a Bluetooth Address at the factory using some random number generation algorithm...
Hello,
this question has been probably asked many times, but I could not find any good matches using the search.
My setup: I am using nRF52832, latest SDK 16.0.0 and a...
Hi everyone, We are doing a prototype with the nrf52840 module and I need to Certificate the board for RF emissions. I have some questions related this:
1- The BLE module...
Hi.. i am using nRF52832 ... 15.2 sdk Version. i'm trying to communicate between a central device and a peripheral.so if multiple peripherals are present and all of their...
1. I use buttonless DFU. As I understand it, at startup the bootloader checks CRC of the application, and if it is ok it jumps to it. So if I accidentally deploy an update...
I tried with the DK and my own USB-serial adapter and both fails at 1M with HWFC with this error:
nrfutil dfu serial -pkg bltest.zip --baud-rate 1000000 --flow-control 1...
Hi I would like to interface the nrf9160 with amw136 (silicon labs) module wifi.
The amw136 has the interfaces: serial (UART, remote terminal), SoftAP and WLAN client (concurrent...
i am working on nrf52832 DK, i am trying to upgrade my development kit firmware using mobile
and i successfully build "secure_bootloader_ble_s132_pca10040.hex " application...
I'm currently using this setup on a fitness device prototype that will send battery status, scores and relevant infos. RPi >>>RFM69 915MHz )))))) ((((( RFM69 >>> Adafruit...
Hi,
I am using the softblink library in SDK 13.1 to control a RGB status indicator LED. It works fine, until I want to change the PWM settings or the LED pin.
The change...
I'm developing an interface I2C to one sensor including SCL, SDA and open-drain return to know if
the sensor is ready to work. After Reset by "Build and Run" form Segger...
Hi,
I'm a new guy for the development in nRF52840 and try to build the application by using 802.15.4. I have two questions, as follows:
Firstly, when I follow the instruction...
