Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
Hi nordic community
I am trying to send stop command to my device(which is connected to my NRF 52840) from my ble module(NRF 52480) after my android disconnected from the...
Hi Nordic engineer:
When I used examples\multi protocol\ble thread\ble_thread_dyn_mtd_coap_cli, I found that the device could not automatically assign LEADER, Router, and...
Hello and Thank you In Advance for Your Assistance. I have been working several days just to get a UART running for interface to a peripheral.
I am trying to connect a UART...
Hi,
As per the document(nrf91_at_commands_v0.9.1) for GPS SNR testing command "AT%XRFTEST=2,1,0" output is single integer as below .
but i am getting output like below...
We are using nRF52832 in our design. We want to collect sensor information along with time stamp. So I took nRF calendar application and tested the same. It was working fine...
I have developed an application that reads data from an analog sensor and transmits data with UART. This app is based off the SDK v14.x uart example, and SAADC example. While...
Hi.
I am developing zigbee product with security function (using install codes).
1. function cmd_zb_install_code in zigbee_cli_cmd_bdb.c, there is a comment as bellows...
Hi, I'm using proxy_client and proxy_server from light_switch examples of mesh sdkv2.1.1. The provision process gets successful with android mobile using nRF Mesh App but...
1. Do I need to make hardware changes when I want to change my SoC chipset with nRF 51 to nRF 52? 2. Does the nRF52 Series require hardware changes when it needs to change...
Hi,
There is a Demonstration about zigbee joining networks by install code.
But how to know if it using the install code instead of the default TC link key?
1. I run...
Hi
I am working on cryptography algorithms. I am trying to write my own implementation of main function. Inside the main function, I wish to call AES functions. I want AES...
Hi,
I am trying to use nRF52832 evaluation board as a BLE sniffer. I have windows 7.
I installed nRFgo studio and downloaded nRF Sniffer v1.0.1.
I plugged the board...
Hi! I'm new developing using real C language. I have more experience using Arduino. I'm trying to send a MIDI message over Bluetooth MIDI when I push one of the buttons of...
Hi,
we've just found the information about the knobattack ( https://knobattack.com/ ).
Is there any fix for this issue with the new updates?
Best regards,
Constan...
