I try to migrate a working code from nRF52832 to nRF5340 with the use of 7002 companion chip for the network part (BLE). However, while I can jump to main and successfully...
Hi,
I am working with nrf5340 chip and I want to migrate from NCS 2.6.1 to NCS 2.7.0. I want therefore to apply recommendations: migrate to sysbuild.
With NCS 2.6.1 I...
I am using MX25 external flash with nRF9160. I am unable to find the configuration to use the Zephyr APIs to access the flash. I am able to access it when I am using
spi_write_dt...
Attribute reporting is automatically handled by the ZBOSS stack which generates the Report Attribute commands. Is it possible to set the Disable Default Response bit in the...
Hi all,
I've followed the instruction to setup nRF sniffer with Wireshark.
But unfortunately, I see this error when I'm trying to start a new capture with my nRF Sniffer...
Hi
I tried to run the sample "hci_pwr_ctrl" from the NCS v2.7.0 on the nRF54L15.
After starting the sample, the modification of the TX power level during the advertising...
Hi,
I realise this is now quite an old version of the SDK and this particular library is no longer supported, but we have not yet migrated our project (I did try once...
Hello,
i'm working on a project where the system will be always in deep sleep unless there is an external event to wake him up. Upon this event, the system connects through...
Hello, I have a question about how to operate on multiple Zigbee devices simultaneously. I am currently developing a hub to control and retrieve data from home appliances...
I want to make a secure pairing with Bluetooth. Let it first pair with the device, then connect directly without pairing. Maximum how many devices can I register?
Hi,
I'm using an nRF52832 in SDK v.17.1.0 and, starting from the ble_app_uart example code, I'm sending data from the board to another device. I want monitoring it with...
Hey all,
I'm looking for a bit of guidance here to nail a bus fault that happens about 30 minutes into the program.
The message is the following:
Reading through previous...
Hello
I am trying to test the esl example project.
Is there a simple, accurate, step by step guide for this?
Current documentation has some incorrect sections and when...
Hi Team
Customer want to use Bluetooth_Base_UUID (00000000-0000-1000-8000-00805F9B34FB) as 128 bit UUID base. They can use any other 128 bit UUID base but this one. When...
Hello, I'm working on an application with precise timing requirements. Basically I need to generate a short pulse and sample two channels during the pulse. In addition, I...
I use the nrf5340.
I want to filter 8 devices with different addresses.
When scan_filter_match() recognizes one of the addresses, can you quickly identify which of the...
Hello, I built a matter-over-thread firmware for nrf52840 on the Matter SDK 1.3-sve branch and NCS 2.5.0 version. It work well with Apple, Google and chip-tool, but commissioning...
Dear sir or madam,
I am facing a peculiar issue. In my application, I am using nrf52840 dongle and I am setting several GPIO pins as output pins with output value high...
Hello DevZone,
I am developing battery powered Zigbee end device. Using nrf Connect SDK 2.6.0 on nrf52840 chip.
I have issue that I am trying to solve. From time to time...
Hello there,
I was using 2.5 SDK on my development. Recenelty I updated the SDK to the latest of 2.7.0-rc3. I got many warnings.
Then, I created a brand new BLE NUS project...
We have a product that uses nRF52832 and works as a peripheral, connecting to mobile phones. Lately we have noticed that in some clients with Android phones, they cannot connect...