Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
We use nRF52840-PDK (PCA10056) with MCU revision Q1AAAA. Given example of secured DFU bootloader (s140) works good. Then we changed MCU on this board to the MCU with Q1AAC0...
Hi to all,
i am working on a project that in it i want use nrf51822 as a peripheral device. i implemented a code but i have a problem, central(cc2540) and peripheral(nrf51822...
Hi,
I am trying to write 16bit, 16Khz, 2 channel PCM data to I2S. nRF52840 DK board is connected to speaker via I2S player/decoder board. I am able to hear audio but it...
How can I determine the correct value pull-up resistor to be used on the TWIM port?
The nRF52832 reference documentation mention an internal 13k pull-up however I've always...
I would like to create a program that was a mix of ble_app_multilink_central and peripheral_temperature. The program would work as follows: when the button1 of central is...
I am trying to migrate a blocking SPI transfer code to a non-blocking SPI Manager schedule call. I have 16 transfers queued up in one transaction.
When I launch it, the...
What is the best way to advertise a custom service and allow BLE connections from a mobile device in a Mesh SDK version 2.0.1 application. Previously I had an application...
Initially I had a project in Mesh 1.0. Everything (provisioning, send&receive) was working fine.
Since upgrade to the Mesh 2.1 there is an issue: provisioning still works...
Hi I've found the documentation around BLE_GAP_TX_POWER_ROLES to be a bit sparse. I was wondering if someone could please give me some more info on them
Three roles have...
I am trying to get the thingy52-mesh-provisioning-demo to work with the SDK for mesh 2.1.1 and nRF5_SDK_15.0.0_a53641a.
I am using the Segger Embedded studio project from...
Hi I'm developing DFU project for my application. I need to have both BLE and UART bootloader. If possible, how can I do that?
Many thanks for the answer
Abele - Ital...
Is there any other way for connecting nRF52 DK with our smart phones, other than through NFC?
My smart phone dosen't have NFC feature and I want to run and test the BLE...
On the infocenter website we can read that ,, The nRF5 SDK v15.0.0 supports nRF52 Series devices''. I would like to use crypto code from SDK15 on nRF51. I am interested in...
