Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
I am using nRF Cloud to update firmware on nRF9160 based products in the field. They are connected via LTE Cat-M on Telstra in Australia. The problem is that the download...
Hi folks,
We got a weird behaviour with our nrf51822(SDK 12.2.0, s130) device. we have built a low power application with following parameters:
MIN_CONN_INTERVAL...
I have tried to understand how data was send from two BLE device. I have had 2 PCA10056 board and I have loaded ble_app_blinky example and ble_app_blinky_c example for each...
Hi All.
I have one question.
I just want to send "volume down key" simplely after connect with android device to take a picture.
I have no idea. and I don't understand...
I modify nrf51 nus in SDK12.3.0 to realize my application, I found when enable uart, the consumption near 830uA , and then call app_uart_close(), the consumption near 5uA;...
Hi,
Is there and C/C++ source code to get float value from 32-bit ieee-11073 FLOAT data type
I need c/c++ code to parse 32-bit ieee-11073 FLOAT data coming from FORA...
Hello,
Using Spi bus with frequency = 4Mbps give me this deformed signals (clock and miso) and when I push it to 8 Mbps I am not able to get the correct values.
Obviously...
When an event is bound to the ppi channel, and this channel is bound to both task_capture and task_clear
can I get the correct COUNT value when an event occurs?
Or can...
Hi all,
I wanna build a IOT gateway. I follow this steps infocenter.nordicsemi.com/index.jsp
When I access coap://[ipv6] It dont have resource light, just only have...
[SDK 12.3.0 / nrf52 DK / Keil tool / beacon example code]
Hello. i am a novice developer.
Power On - Beacon data transmit and enter to sleep mode after 10 sec
...
I fail to integrate “ble_app_multilink_central” and the uart portion of “ble_app_uart_c”
I have checked other posts and it is inconclusive if and how they got the integration...
In traditional approach to ESB communication we have many PTX device and one PRX device:
In my application, situation is inverted: I have only one PTX device and many...
The function peers_id_keys_get() (SDK 12.3.0 Library id_manager.c) returns Error BLE_ERROR_GAP_INVALID_BLE_ADDR (0x3202) when the peer device address is neither PUBLIC nor...
Hello,
Have been reading the example codes and documentation in order to connect an ultrasonic
sensor to nRF52. The goal is to read in the value and then send it over...
