Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Is there a plan to fix this errata limitation from errata limitations documented on softdevice?
If Radio Notifications are enabled, flash write and flash erase operations...
Hi all,
I'am using nfc url record from nRF5_SDK_11.0.0-2.alpha.
The example works fine on PCA10036 but not PCA10040.
No ITs are generated on µC.
I'am using Nexus 5X...
I am developing an code which requires use of multiple Timers.
I am using Sdk 11 here when i try to initialize timer there is no field for APP_TIMER_MAX_TIMERS in APP_TIMER_INIT...
Inorder to create a c++ wrapper in nordic SDK , i have to
change the Makefile so that it can compile both C++ and C.
in the example the makefile already has gcc added but...
I would like to have BLE using 51822 and audio using a separate BT classic chip on my device. Are there any products in the market that use separate BT chips for LE and classic...
Hello everyone,
I would like to ask that when my project will get the event(BSP_EVENT_SLEEP、BSP_EVENT_DISCONNECT and BSP_EVENT_WHITELIST_OFF)
With the example,in the...
Hi,
I am evaluating the NRF52 with PCA10040 board and nRF5x_SDK_11.0.0.alpha.
I want to create Wave Forme as below.
Out[0] pin transit low to high at compare 0, Out...
I noticed S110 is not listed as supported by nRF5 SDK11. However, no supported SoftDevice seems to offer the same functionality as the S110 (Peripheral only protocol stack...
Hi,
in SDK v9, i tried to compile the bootloader example, but:
/usr/lib/gcc/arm-none-eabi/5.3.0/../../../../arm-none-eabi/bin/ld: region `FLASH' overflowed by 6944 bytes...
Did anybody know how I could determine the connection interval for a established ble connection between an android (4.4) central and a (e.g. nRF51822) peripheral?
I've been having a little bit of an issue trying to parse UART data that I am receiving from an external device.
Where I'm having issues right now is comparing an incoming...
Every 10 packets send; it will have at least 1 packet with 1-2 bytes corrupted data.
The configuration as below:
data rate: 2Mbps
channel: 7
Prefix0: 0xE2
BASE0...
Hi,
We have an application that can run in two modes. The mode is selected by setting the GPREGRET to 1 or 0 and restarting.
Currently we are running this procedure directly...
