It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
Background
For reasons that I do not want to dispute here, I am building a custom bootloader for the APP + NET cores on the nRF5340. This custom bootloader is not a Zephyr...
I am testing out the nRF54H20 on the nRF54H20-DK version 0.9.1. I have followed the steps for setup in the "Getting started with the nRF54H20 DK". I currently have nrf54h20_soc_binaries_v0...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I'm trying to run the DFU sample l9_e5_sol on a custom board using the nRF5340 and SDK version 3.0.2.
My goal is to perform DFU over BLE using external flash. However, before...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
I need to use a high speed PWM (> 500 kHz) in which I can vary the pulse width. In examples, it's handled in software which is too slow.
Is there any way to set a pin on...
Hi,
I am having some problems getting the s110 SoftDevice working (sd_softdevice_enable stops the program execution) on a custom PCB. I have seen several issues similar...
Hello,
I Preparing the KC (korea-certification. about bluetooth)
KC requirements as follows:
Set Test Modes
Set Continuous modulation mode
Set Unmodulated...
I'm interested in getting started with NRF51, but the full DK is quite expensive here and I don't need it. Does the nRF51-Dongle sku come with a key for downloading & using...
Hi,
Can someone tell me (definitively) what the max SPI clock speed is?
I have seen 2,4 and 8Mhz here and in recent documentation and I'm confused.
Thanks
Hi
I have been experimenting with encryption and bonding and I think I don't understand completely the bond procedure.
To bond a device, it is necessary using the bond...
HI ,all !
I have a question about PORT event function.
as the 4 channels of GPIOTE (channel0 to channel3 ) have been used for other usage.
i need to use a general IO...
The only documentation I can find for s120 is part of the nRF51 SDK . Though it isn't clearly stated the SDK assumes release 1.0.1 of S120 is being used.
The v2.0.0 S120...
Hi
I got some questions about KEIL MDK uVision5.12 PACK.
I tried uVision5.12 PACK to install Nordic SDK package. Currenly, their latest version is v7.1.0.
If...
Hi,
I get 0x2001 error in spi_master_close() at the following 2 lines.
/* Disable interrupt */
APP_ERROR_CHECK(sd_nvic_ClearPendingIRQ(p_spi_instance->irq_type));
...
I got my UART working just in basic sending and receiving.
Now I am trying to implement buffer feature and other non-blocking features. I have done this on other CPU's many...
I've been playing with the simple_uart example and it seems like it might be missing responses. Does it buffer incoming data until the simple_uart_get() is called?
Hi,
I searched through the devzone but I cannot find a answer on this question but the question has been asked before.
Some background. I have a working solution from...
