Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hello,
I'm trying to build the trusted firmware M for the nrf9151.
I did the following steps:
git clone git.trustedfirmware.org/.../trusted-firmware-m
cd trusted...
Hi,
I am working on a project where there are moving devices. Devices can only move if a wired button is pressed. In fact, for security reasons, there are two buttons connected...
I've been looking at this for the better part of a day and can't seem to pinpoint what I'm doing wrong here. Does anybody want to take a quick peek at this project and tell...
Hi,
I would like to use the PCA10000 dongle hardware and antenna design for my PCB, i got some questions:
1)I have just UART pin outs extra, I would like to reduce the cost...
This question relates to the unofficial gcc Makefiles available here:
github.com/.../nrf51-pure-gcc-setup
These are great and I've managed to get as far as compiling...
To all successful developers.
I want to write some predefined parameters into the stack. So the problem is the adress.
Example: The nRF51 is part of a medical device....
hi,
is it possible that we can use s120 stack as a central, at this stage to work with our customized profiles?
or it will support only SIG profiles
regards & thanks...
Hello,
I've completed the ble iBeacon like application we are working on, with some custom GATT services/characteristics as well.
When I use LightBlue on a MacBookPro...
There is a check box on nRFgo Studio, Lock entire chip from readback. But a lot of chip can not burn one by one
Can I use AES block encryption to do this?
Hi
We are investigating Hong Kong certification for our nRF9E5 based equipment in the 868 band
The snag seems to be that required channel centre frequencies are "odd...
Hi,
My setup is a nRFgo QFAA FA with S110 v.6.0.0 and Motherboard. I am using the latest SDK 5.1.0. The Master Control Panel drives the nrf51822 USB development dongle...
Hi,I have a Nrf8001 module, use a arduino to control it.
Now,I can use this module to connect IPHONE APP(BLE Probe and LightBlue),sending and reciving data are all ok,the...
Hi Nordic Devs,
First, thank you for excellent documentation and sample code for use with your hardware. It's been tremendously useful already!
I'm pleased to own an...
Hi,
i have some trouble with my watchdog in application. If i does a System_reset (no SD Method because i disabled it before) it sometimes top at this point and does nonsense...
Hi,
We'd like to using nRF51822 to setup an environment which have 2 peripherals and 1 multi-connection central.
Peripheral 1 : reading some data from the car(OBDII...
Hi, we add two characteristic as TX/RX.
We are ready to use them to transmit data and receive data with phone
One for transmit the control command and get respond command...
