There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
I was facing some buffer issues while setting up I2S, so I decided to flash and test out the i2s echo sample provided in the sample programs in the SDK. I changed the DT_NODELABEL...
I wanted to get FOTA running on a PineTime devkit board (nrf52832) just to test and see if it works, but am getting the following error message:
/opt/nordic/ncs/toolchains...
Hello
We have developed a device based on the nRF9160, one of our potential clients asks us if the device has High Priority Access, he says that this information should...
Hello!
im trying to write chunks of bytes to an sd card in a non blocking style. One possibility im pursuing is to use SPIM, where the actual writing is done by DMA-Controller...
Hello again,
I am putting together a device that need a lot of local non-volatile data and uses a lot of flash on my NRF52833. I am running NRF Connect SDK 2.6.0. I'd like...
Hi there,
I'm encountering an issue while attempting to establish an Internet connection on my Linux machine using the nrf9160 DK SLM (2.6.1) application. I've flashed the...
Attempting to get up and running with the basic zephyr lvgl demo found in `zephyr/samples/subsys/display/lvgl`. Text appearing on the screen is of poor quality but still legible...
Hello,
We are currently developing a WiFi library and just started on implementing HTTPS and ran into some issues. Since we don't have enough flash and memory for using...
Hi everyone,
I’m currently working on setting up Azure communication using the latest SLM version for PPP (Point-to-Point Protocol) support. Here’s the configuration I’m...
We have a Waveshare display and a npm1300dk and I wanted to know the proper way to add the npm1300's config.overlay file, generated by nrfConnect's PowerUp, to the west command...
Hi,
I faced some issues regarding multiple IRQ_CONNECT being onvoked on the same irq and I went into this post :
LPUART nRF5340 fatal error - Nordic Q&A - Nordic DevZone...
Hello! I am using nRF Connect SDK 2.6.0v. I created a west workspace and i want to make custom board. I took reference from Devacademy nRF Connect SDK Intermediate Lesson3...
Hello Nordic
Use NRF52832 、 NCS 1.6 、“zephyr\samples\basic\blinky” sample.
In hardware, my board doesn't have a low-speed clock, and the reset pin is floating. Therefore...
Hello List,
I have an Arduino Nano 33 ble with nrf52840. It is powered directly with 3.3 Volt using 7 Volt and a 3.3 Volt LDO voltage regulator. It is programmed (via the...
