Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hello. I am developing a central operation using nrf52832 (S132 v7.0.1, SDK v17.0.0).
There is a numeric comparison as an authentication method, can I do it with sdk17.0...
Hello,
I'm new with Nordic products, and I'm trying to use my New dev kit nrf5340 DK.
The request today is about my code, I implemented my code in the DK, and now I want...
i have nrf52832 and softdevice s132. i want to calculate throughput. i tried running ble_att_mtu_thorughput example and read https://www.novelbits.io/bluetooth-5-speed-maximum...
Hi,
when debugging BTmesh (with MPSL) breakpoints trigger an assert. This is listed in the known issues of the nrfConnectVScode page:
https://nrfconnect.github.io/vscode...
Hello, i'm trying to flash a code in my module nrf52805 thx to my Dk nrf52840. i have this error I followed the instructions here: https://devzone.nordicsemi.com/guides/short...
Hello,
I want to build a configuration where MCU Boot secondary partition is in the external flash and QSPI data encryption is turned on.
I modified the nrf_qspi_nor...
Dear, I want to interface nRF5340 to normal 16x2 Alphanumeric LCD running on 5 Volt. Are the Port pins of nRF5340 5 Volt compatible when nRF is running with 3.3 Volt supply...
Hello,
After succesfully configuring the W5500 driver using Zephyr, I am trying a few examples in the given samples (socket echo). I am unable to send or receive / ping...
On the nRF5340 P0.00 and P0.01 are used for the 32.768 kHz crystal by default and are not available as GPIO on the connectors.
how to remap this pins to gpio?
I need to develop a pair of BLE-capable devices that talk to each other. The communication between them will be very simple - the central needs to tell the peripheral the...
Hi,
When the NRF9160 boots the GPIO level of a given pin, such as P12, is set to high (3.3V) before the main application gets a chance to call gpio_pin_configure and gpio_pin_set...
I am now using the DFU functionality to upgrade the code combined with the CoProcessor and radio_test samples and find that the code takes up too much space to upgrade. I...
I recently bought Thingy:91 (nrf 9160) there was a SIM card included but it didn't work! I have written to support twice at the recommended address [email protected]. it was...
Hello,
I am using PCA10040 DK for the programming with ble_app_beacon_pca10040_s132 example code. I want to broadcast my 20 bytes of data with my 0xFFE0 UUID.
In this...
Hello,
I am using the nrf52840dk_nrf52840 with NCS v1.7.0. I am trying to use the external memory (MX25R64) to host the mcuboot_secondary slot. Then, the primary slot...
