When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Dear ,
With nRF connect SDK, is there a way to check if the SD card is formatted with the correct file system, i.e. FATFS? If it's not in FATFS, how can we format it via...
We've upgraded our nRF9160 modem firmware and would like to downgrade to the pti_v1.1.x image so that we can test production test commands such as %XMIPIRFFEDBG. Where can...
Is there any info, which helps to distinguish between the versions of thingy 91 when ordering?
According https://www.nordicsemi.com/Products/Development-hardware/Nordic...
Hi Nordic Team,
I have a custom application running based on nRF NCS 1.5.0 with MCUboot enabled.
I'm having an issue where MCUboot simply doesn't jump to the application...
I had to reinstall Keil after running into some issues and lost most my packs. My project uses the NordicSemiconductor.nRF_DeviceFamilyPack.8.15.0 and the NordicSemiconductor...
I want to expose 2 endpoints on the nrf52840 DK - one is the existing Onboard LED and the other is the GPIO pin (P0.02) which I have enabled in overlay.
I am extending the...
Hello,
We are using A-GPS in our application to get faster TTFF and will be reading location coordinates after every 5 mins of duration. The application flow looks like...
Hello, On a custom board, using the NRF52832, we want to know the value of a potentiometer. This value is send via a signal on the AIN5 pin of the NRF52.
So, I tried to...
I am using nrf52833 to make a Thread end device as SED and RCP. All firmware versions use NCS V1.8.0.
The compilation options for OTBR is: CMAKE_OPTIONS += \ -DOT_THREAD_VERSION...
Hi,
I use the BLE_APP_UART example for reference and in the code there is the ble_evt_handler with the following states:
case BLE_GAP_EVT_CONNECTED: case BLE_GAP_EVT_DISCONNECTED...
Hi,
I faced the exact problem nda , here . I take step just like nda did before. I unchecked "Enable debug options" as Marte Myrvold told, but still the same problem.
...
Hi,
I'd like to test the Adafruit NFC reader example provided in nRF5_SDK_15.3.0_59ac345. I'm using a nRF52832DK and I2C communication, as shown in the picture:
The...
Dear Nordic Support Team,
I am developing an application for the nrf9160 DK version 1.0.x (nrf connect sdk 1.8.0 and modem firmware 1.3.1). The application depends on other...
I have a project that is reading an external flash chip via qspi. Everything is working well, and I haven't defined the sfdp-bdp field in the overlay file that defines the...
