I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
I have a module using a Nordic chip labelled "N51822QFAAH01621UT". I know it's the NRF51822-QFAA, but I am not sure which model exactly?
Looking on DigiKey these are the...
This is more of a question than a problem:
I have been studying the ble_app_uart_c code and noticed that although data is transmitted to the handler one byte at a time,...
Hello.
We are looking for a viable solution on how to transfer a firmware over the BLE OTA from Particle Tracker (Gateway), or any other mcu to nRF52840 devkit (Client)...
Dear, I am new to Nordic. I trying to understand the various Defines for nRF5340DK kit using Devicetree.dts file. In that, I had look on SW0 defines.
1. The gpio0 reg is...
Hi, I'm using the nrf52840 BLE mesh (nrf5_SDK_for_Mesh_v5.0.0_src) and some other sensors which drivers are written by using nRF5_SDK_17.0.2. my device is battery operated...
In nRF_SDK_for _Tread_and_Zigbee, we used to set autocommissioning as false in the "thread_configuration_t" configuration and then start joined so that my thread node used...
The examples include checking the return code from various FDS calls immediately after the call.
Only some errors can be detected at the time of the call (for example NULL...
Hi,
I have created a vendor model for my application. When sending a message of 32bit it's working fine, but when I am changing the message length to 64bit by doing necessary...
Hello,
I am using a modifed Secure bootloader example in my NRF52840. I would like to show the user an update progress bar on the device screen while loading BLE DFU update...
Hello!
I am facing some strange behaviour using nordics dfu update service on android.
Somtimes after starting the dfu upload the app is not able to connect to the dfu...
Hi,
How to get this done using TWI this temperature sensor's I2C to write 16 bit register, it is sending start after device address then data. I tried as below, but it will...
Hi, I want to be able to send 1bit of data with as low latency as possible, what is the best way of doing this? Can i in some way directly control the low level of the radio...
Hi All,
i am using the below link to flash the bootloader
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/device-firmware-update-dfu-with...
Hello,
I am using Eclips & ARM tool chain for project with BLE functionality. I tried to import this code in Segger embedded IDE but it did not worked. This project is old...
