I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi, all.
I'm using nRF52833 and trying to communicate ESP8266 using UART.
I already successfully communicate with Dust Sensor with baudrate 9600, so I tried to communicate...
Hi,
I'm trying to find an example of using the I2S audio interface with the Zephyr RTOS on the nRF52840dk_nRF52840 development board or on an nRF52840 device in general...
Hello ! I'm a beginner here, and I have a problem that I struggle to solve. A few years ago, a firmware was done by a company, for the one I work for. It was done with IAR...
Hi,
I am toggling a GPIO using the below code and trying to find out the relation of the frequency and the code statements. I know that GPIO peripheral is running at 16MHz...
Hi,
after fixing a missing ground in my setup (see devzone.nordicsemi.com/.../interaction-jlink-and-power-profiler-ppkii) I have not been able to get less than 50uA of idle...
My B0n bootloader (running on the network core) is trying to access XIP space and faulting. This is a part of an network core upgrade.
From what I can learn from the data...
Good evening,
I’m testing the SDK v17.1.0 “Open Bootloader with DFU” example. I’m using Segger Embedded Studio to program my Nano 33 BLE via the debug interface (P20) of...
Hello again Nordic World!
Yet another question about getting RSSI values:
Again, using 10028 and 10040 boards under sdk 12.3.
Is the adc acquisition of rssi done synchronously...
Dear DevZone,
within out project we make use of an esb communication between a nrf52840 DK connected to the PC via USB (a "station"), and a custom PCB with a nrf52840 micro...
Hi all,
We are developing an application using nRF52840 device and the idea is to enable the device with peripheral and central roles.
We would like to set two advertising...
Hi there,
We've been doing OTA DFU updates for a while now, but a recent increase (by one page = 4kb) of the firmware has created an issue.
Flashing through USB serial...
Hello,
I am using nrf9160 development kit. I need to use this dk with Modbus RTU master slave project. My question is does nrf9160 support for work on Modbus RTU master...
Hi Nordic,
I've reviewed the Mesh PyACI which uses a serial connection with a DK to provision a separate Mesh device over-the-air, if I understand correctly. But is there...
According https://www.nordicsemi.com/Products/Development-hardware/Nordic-Thingy-91/Download#infotabs
Version 1.2.7 seem to be the latest without "only for testing and development...
