Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
Hi all,
So I want to give you a full description about what we are doing because we could not understand what we did wrong.
Our DK : dk-51
Soft Device : S130_v1
Our...
Description:
I try to initialize a SPI device in my nRF52DK through the Zephyr‘s driver(drivers/spi.h).
Code seems correct when compile and I got no error when build the...
Hi, I am new to Zephyr and Nrf, I am trying to replicate the event manager arch from asset tracker v2 but I am stuck in the setup. I am trying to use the logging capacities...
I am working on the Electronic Braille Display for visually challenged persons.
Our device will communicate with Voice over service on the laptops and smart phones using...
Hi,
with %SHORTSWVER: nrf9160_1.3.1 I am getting:
AT%CMNG=0,3,4,"test1234" OK
AT%CMNG=0,3,3,"30313233343536373839303030303030" OK
AT%CMNG=1 %CMNG: 0,6,"0606060606060606060606060606060606060606060606060606060606060606...
I have a single sample of the new nRF52840_XXAA at hand on our custom board. I'm trying to do a --recover with nrfjprog. As the log below shows, nrfjprog recognizes it as...
Hello ,
I m using SES v5.6 and NRF52805 ,ble_app_uart ex (nRF5_SDK_17.1.0),
Requirement -need to wake up and reset ( or start advertising again) from sleep mode ,when...
Hello,
I have adapted some of the ESB proprietary Protocol from the NRF SDK into my own project without installing the SDK directly; however, complete integration seems...
Hi Team ,
In my application , i am using RTC1 for RTOS and RTC2 for Running a time calibration andRTC0 for Softdevice but parallelly i need to add Lbs service which includes...
Hi there,
I wanted to test Matter/Thread networks using the nRF5340DK I have.
I downloaded the nRF Connect SDK through the Toolchain manager.
I tested the blinky app...
Hi,
I have an unusual requirement where the current constraint device needs to the controller and passively scan. My understanding is the best way to estimate the current...
Hi Nordic Semi
I have implemented a basic BLE peripheral on a nRF5340 using the nRF Connect SDK 1.7.0.0.
The product we are developing have strict power consumption requirements...
I've been able to port the DFU process into a C# app running within a Linux gateway.
I'm using the buttonless without Bonds service to enter DFU mode.
The problem I have...
I am trying to find information on this and it is not clear.
Is it safe to perform FDS read operations (i.e. fds_record_open(), fds_record_find() and fds_record_close()...
Device: nrf52833
SD S140
Application - Central Host, based on uart central sample project
The peripheral device needs to deliver a block of data (10-20K bytes) to the...
