Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Good Afternoon, I recently got an nRF5340 PDK kit and would like to get OpenThread examples for this board.
If possible I would like to demo the OpenThread CLI example....
I'm using this code to handle interrupt and power down the device. However, this code is not working the softdevice.
I just want to power on and power off using an interrupt...
Hello,
I am working with the nrf_cli_ble_uart (SDK16), I am able to connect, exchange data, however when I disconnect I got an assert :
It is indeed in ble_nus.c ...
Hi Nordic Team,
I am using a simple GPIO (tx/rx controlled via GPIO) FEM (PA/LNA) with connected to nRF52840.
I know I am allowed to crank up the TX power of nRF to +2dBm...
Is there support in NCS for MCUboot images encrypted with a different encryption key (not the same key as the signing key)? How is that configured (via prj.conf, etc)?
Hi, I have a nRF5340 based target board running SMP server plus MCUmgr. My ultimate goal is to reproduce on Windows the DFU over serial I already do from Linux. Tese are the...
Im trying to interface ADXL345 with nrf52DK via I2C. Im using the reference drivers in below link
https://devzone.nordicsemi.com/f/nordic-q-a/40822/adxl345-and-nrf52832...
Hello,
I am trying to connect a BLE HRM strap with nrf52382 using example/ble_central/ble_app_hrs_c/pca10040/s132
I am getting this on debug
<info> app_timer: RTC...
Hi,
I am having issues programming my custom nRF5340 board and was hoping to get some advice on the issue.
When programming using nRF Connect for Desktop (Windows 10,...
Device nrf52832 Custom board and nrf52DK with nrf52832
SDK 17.0.0
IDE Segger
when SPI interface is initialized by nrf_drv_spi_init, then MISO line behaves as follows...
Hi! Recently I have been working with Nordic products, starting with NRF52DK. I want to pair/bond cycling equipment (BLE and ANT+) with NRF52DK. After no success with ANT...
I am using pc-ble-driver-py to create a custom scanning and connecting application, but I'm running into an issue regarding the UUIDs of a particular service after connecting...
Hi,
I'm able to successful download and flash my application firmware using AWS S3, but unable to use Microsoft Blob Storage successfully.
I'm using Thingy91 with SDK...
We are currently developing for a product that uses the nRF52832, using Segger Embedded Studio (SES) 4.52c, and the ARM GCC toolchain (2019 q4 version.
We have set up...
