Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello Nordic
I am working with nrf52832, sdk 16.0, softdevice s132
I need to advertise NON CONNECTABLE ble with changeable data (later relevant data will be received...
Hi
we are using the nRF52840 and antenna signal i connected ceramic chip antenna(ACAG020-2450-T).
The above attached schematic of ant signal matching circuit schematic...
The only way I can see to do it is by two separate PPI calls. So Timer1 "tasker" is firing both the capture and clear... but will they execute sequentially?
Hi,
I just bought the NRF52850 DK. Currently I do not have the JLink connector to perform debugging using UART.
Is there is a way I can print printf or NRF LOG through...
Hello expert,
I would like to design a custom PCB that has two transceivers on it. One transceiver is working as a beacon/continuous wave generator (TX) and the other one...
On the basis of NRF24L01 +, an antenna was designed. after designing, I need to carry out the coordination of circuits. Do not tell me how best to do this, what values to...
I had a setup where I could DFU OTA a NRF52832 based board
I moved to a NRF52840 based board and now during the OTA DFU I get messages like this
I did try a new bootloader...
Hello, guys.
We have nRF9160DK and nRF Connect SDK v1.3.0. The version of the LTE modem firmware is the latest (v.1.2.0).
In our design, we are able to initially connect...
Hi Nordic team,
I just purchased a row of new nrf9160 SiPs for our IoT products. We are testing with new made cuicuits.
We use the same circuit schematic that worked with...
Hello,
Problem: BLE doesn't work on a OurBoard with nRF52840 (Schema1).
1) BLE example is working DevBoard (can see BLE server by scanner). On the OurBoard the examle...
Hello,
I've been testing HCI_UART from Zephyr RTOS on nRF52840DK and own device which has nRF52840 + FT232R as USB-UART converter. Regarding the own device it's a circuit...
I am studying the beacon example provided in the SDK (The project is found in following directory C:\Nordic_semi\nRF5SDK160098a08e2\examples\ble_peripheral\ble_app_beacon...
Hello there, I'm developing a device who will use two NRF52832(ANNA-B112 Module). They will communicate as central and peripheral. But i'm facing a problem, i need to after...
I could decrease current consumption at v1.2.0, but couldn't at 1.3.0. 520uA flows in k_cpu_idle();
How can you do that?
Also, in v1.3.0, CONFIG_UART_0_NRF_UARTE is depricated...
