Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello
I am using nrf5340 raytak board which does not use DC_DC power, uses internal quartz. When I play the Bluetooth peripheral example I get the following error(I using...
I'm trying to build a simple water leak detection system. The sensor would need to alert a user through SMS/mobile notification when a leak is detected.
I was thinking of...
hi, I am working on to combine USBD CLI and RTT to USB HID with SDK 17.10, configuration as below
pls see below mainloop:
other codes are based on example of USBD...
This is driving me totally nuts. There are inconsistent pieces of information in documents and code. I am getting a modem reset loop problem. The documentation says the timer...
Hi,
Long story short, I made some boards using nrf9160 modules, received parts from DigiKey, soldered but can't make them work, at all.
nReset pin is stuck low. Tried...
I am using nRF52832 for high-rate sensor.
Of course, I can use SPI using CPU but it's busy for other jobs.
So I want to use DMA if it's possible.
Currently I am using...
I am using the nRF5340 and trying to get MCUBoot working. I am running into problems and looks like I need to edit the MCUBoot code, the problems are long and numerous too...
Hello everyone,
I'm using the Bluetooth Peripheral sample UART and have noticed an issue.
When I perform a lot of sequential pairing requests followed by cancels from...
I recently bought this display that is 64x32 pixels and uses the SSD1306 driver . When running the LVGL Basic Sample with the Zephyr ssd1306 _128x64 shield , the display works...
NRF52840 uses 2.5V power supply. We found that when the voltage drops below 1.7V, even if the voltage returns to 2.5V, the entire system cannot work and JLINK cannot connect...
Hello,
We are using the npm1300 PMIC to run the nrf5340 VDD at 1.8V. If we connect D+ and D- from the USB port directly to the D+ and D- pins, will the USB peripheral...
I am developing a custom nrf5340 board design, that is using the BL5340PA external antenna module to implement the nrf5340 chip in the design. The BL5340 module allows all...
Hello,
I am purchasing a RAK4631 module, and am looking for an alternative for the J-link single step debugger. I saw that this product had a o n-board SEGGER J-Link debugger...
