Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
hello. Is the nrf5340 network core supported DFU with Single Slot? Not Dual Slot. If it is supported , can you tell me the URL describes how to DFU with Single Slot.
Hi,
I am trying to get the MQTT publisher example working on my nrf7002DK board. For this, i have done the following things
- SDK version: 2.6.1
- Board selected: nrf7002dk_nrf5340_cpuapp...
1. What is the antenna output of the DECT NR+? Is it the same pin as CAT-M/NBIoT antenna output? (i.e. pin 35) 2. In Section 8.3 of OPS document about DECT NR+, it mentioned...
Hi,
I am having similar error as reported in Case ID: 308488, however here issue is running z-test on provided Nordic test samples.
(note: nRF-connect SDK, works as expected...
Hi, I have a question about SDK. Why not a single example build out of the box in SDK. As a beginner to learn about nRF devices, if i have to face all these weird issues in...
I would like to monitor the states of switches sw0 and sw1 on my nrf7002dk board using GPIOTE interrupts.
Initially this is just for example purposes.
I eventually need...
sdk: 2.5.1
cpu: nrf5340
I have a bootloader which have a big ram block for upgrade purpose (around 250kb) in bss section (I will move it in noinit, but it is not the point...
Hi,
I am using nrf52840. we have already used 3 SPI instance (SPIM1, SPIM 2, SPIM 3). wanted to use one more SPI instance i.e. SPIM 0. but if I enable this I am getting...
Hi,
TWIM does not work well with nRF5340DK as shown in the subject. The conditions are shown below. - I/O voltage is not 1.8V. The waveform is distorted around 2.5V, though...
Hi,
We are developing a device using the nRF5340 DK and need to add external Flash memory accessible via QSPI with XIP, as the available memory is insufficient due to DFU...
Hi all,
I am very new to the nRF controller. Previously, I have worked with STM32 controllers.
Currently, I am working on a project with the nRF5340. I am having difficulty...
Hello,
In the past, i have posted a ticket to ask can the CIS and BIS modes work simultaneously. The answer is that it is feasible in the future.
Can CIS and BIS modes...
Development Software: Segger Embedded Studio, nRF5_SDK_17.0.2_d674dde
Project consists of an nRF52DK-based peripheral (remote control) and a custom nRF52832-based central...
