There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
I need a checksum to verify integrity of some data blocsk. As I saw, that the nrf5340 hardware has some builtin support for SHA-256, I though: cool, let's use SHA-256
Now...
Hi,
I build a custom board (nRF52840) but I'm not able to flash it using nRF5340DK with J-Flash via SWD interface.
1. The first thing I did was to do a full chip erase...
Hi,
Is it possible to communicate with the nrf52840 dongle from an android application via USB port ?
That is, nrf52840 dongle will be inserted to the android phone's...
Take Bluetooth UART as an example, there will be a delay in the process of sending data from the peripheral device to the central device to receive the data.
What factors...
Hi, I'm developing for a custom project board which only has the SWD pins exposed, which I'm using for (1) programming and (2) RTT logging during development.
Once the device...
I'm working on adapting ST's RFAL NFC library for ST25R3916B/X-NUCLEO-NFC08A1 on an nRF5340/DK in order to emulate an NFC tag, and would appreciate some insight into how Zephyr...
Hi, I use NCS v2.6.1 I have taken Central and peripheral HR as an example and am trying to modify it to make the Central/Peripheral UART example work similarly.
I briefly...
Hello,
I'd like to add the transmission of an I2C recovery pulse (where you toggle SCK 10 times) to my startup routine for an offboard device whose state I'm uncertain of...
Hello Nordic team,
I was wondering if it's possible to start the MCU boot from the application at runtime.
What I want is to be able to restart my product and run...
Exercise 2 doesn't seem to work for SDK v2.6.1 with v2.6.1 toolchain. SDK v2.5.1 works though. What configuration or code changes do I need to make it work for v2.6.1?
Hello,
I was curious if there was a project that uses 2 Mbps BLE to connect two nrf52840s, preferably with the ability to change which BLE channels the devices use. I...
In our custom board, check flash write and read using sample (C:\ncs\v2.6.1\zephyr\samples\subsys\nvs) but showing following response. the same build working fine in nrf7002...
This issue is for a programming environment on a macBookPro.
I finally get the system tamed and got to the point of testing the various sample apps provided. I wasted a...
1.Created a composite device for CDC and MicPhone. When the registration of mic SOF is interrupted, the device may not recognize the issue
ret = app_usbd_audio_sof_interrupt_register...
I would like to develop DTM and normal BLE stack operation in single firmware by NCS. Basically i will check a GPIO, go DTM test mode if GPIO short to High, go normal BLE...
