There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Please find below my config for handling Interrupt calls.
I've tested on another sensor dev board that the sensor I use is properly set up and is sending INT1 and INT2....
Hi everyone,
I am working with nRF52832, I am trying to implement the Zephyr Modbus client example onto it, but i keep receiving the following errors.
There is this...
Hello everyone
I'm trying to connect 2 board nRF52-DK (PCA10040) via modbus RTU using zephyr example (client and master in 2 different board).
I'm using visual studio...
I just installed the toolchain (2.6.1) and SDK (main) from scratch, and I'm not able to build the Serial LTE Modem and Asset Tracker application. I receive an error during...
Hi There,
Are the GPIO levels high impedance when the system is in off mode? Can you give information about their status? For example, one pin of the device is configured...
Hi there,
I'm on Ubuntu 22.04.2, 6.5.0-41-generic kernel.
I've been trying to setup the nRF connect toolchains & SDK through VSCode. Things seem to install fine, but when...
Hi,
I have a solution that every 15 minutes needs to perform a WiFi Scan and save the BSSIDs that it finds. Sometimes it will find the maximum number set and will complete...
I am getting an error message when trying to use a nRF5340 DK with a Waveshare 1.69inch Touch LCD Module on the Zephyr sample code with minimal modifications. When I flash...
I'm using custom board of nrf5340 with nrf7002.
Use helloworld sample and have set "config serial=n" and "config device pm =y".
The current is 90 ma when I don't do anything...
Hi,
I have new requirements for nRF52832 using the NRF Connect SDK to develop firmware. I want to know how it supports audio playing with the I2S MAX98357. Is there a possibility...
I am working on a pdm microphone using nrfx pdm driver (INMP621) When I am saving the pcm data into .pcm file using sd card and playing the .pcm file in Audacity I am getting...
I'm using nRF52840 with nRF5_SDK_17.1.0_ddde560, using the ble_app_multirole_lesc example file.
When I set extended = 1 in scan_init , the debug session jumps to NRF_BREAKPOINT_COND...
Hi All,
I flashed an nRF5340 DK board with a samples/bluetooth/hci_uart image and one more nRF5340 Audio DK with a samples/bluetooth/peripheral image.
I have not made...
